To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4231 (+10)
  Re: Looking for Mac prog environment
 
Dave Baum just released the latest version o NQC (Not Quite C) for the Mindstorm system. It runs on Mac, PC, Linux. (URL) you prefer a graphical/pictorial interface on your Mac like that of the Mindstorms system for the PC, try RoboLab which is (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: Where do I get Spirit.ocx?
 
Can you describe how you run the regsrv32.exe on Spirit.ocx? Sorry for the dumb question but I am not firmilliar withregsrv32.exe. By the way are you at Western Washington University? If so are you a student or on the faculity? Thanks Jim Clark (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  RE: regsvr32.exe (was RE: Where do I get Spirit.ocx?)
 
From the Windows Command Prompt: "regsvr32 spirit.ocx" should be all that's needed. Or, to unregister it would be "regsvr32 /u spirit.ocx" Chris Kent & I are both students at WWU. -- You'll probably see many WWU CS students appear on this list, b/c (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  More outputs, thinking outside of the box...
 
With all of the ideas of mechanical linkage flying about for getting more controllable outputs for the RCX, I couldn't help but think, "there has GOT to be a better way!" How about this idea. Its even all-lego. Use your three outputs in one mode (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: More outputs, thinking outside of the box...
 
Dennis - How can you make use of the 3rd. motor if it needs to be available to bump the switch? Also, how would you deal with the polarity going to the 2nd set of motors? Thanks --- John. (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: Sensor readings on the RCX display
 
You can also force it to run the output. Press and hold view while its pointing to a output, and then the Pgrm and Run buttons work to run it forwards and backwards. Its a bit of a pain to use, but nice when prototyping new mechanical creations. (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: More outputs, thinking outside of the box...
 
(...) Often you don't need continuous motion, eg. robot arm, and you can keep to a limit. If you use another bump switch to tell the RCX that the motor shouldn't turn any more you can stop the action before you get to the second bump switch that (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: Bowing out of Joel's challenge!
 
Here is a rudimentary page with some pics of what I had. Important points to note: - This bot was designed to deal with empty cans only - Last design had 3 motors - but I was planning to eliminate one (hopefully) - I am an inexperienced hacker when (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: More outputs, thinking outside of the box...
 
Dennis - Check out my solution using small relays at: www.truepicture.com --- John. (...) (28 years ago, 11-Mar-99, to lugnet.robotics)
 
  Re: Ultimate Starter Sets / Add-Ons for Mindstorm? Reprise
 
Mindstrom fans seem to go through a lot of grief finding or ordering just the right set of parts. I recently read a memo on the 'net lamenting some of the shortcomings of the Lego system: it is difficult to build certain structures, things must fit (...) (28 years ago, 12-Mar-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR