To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 3021 (+10)
  Sensor monitoring
 
I have a project that I am building, it is a finish line monitor for a pinewood derby track. What I am doing is putting two light sensors above the track pointing down so the ambient light will change when the car crosses the finish line. One sensor (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Sensor monitoring
 
To my knowledge the LEGO firmware executes one instruction at a time for each task, so there is one and only one instruction being executed at a certain instant even if you have multiple tasks. Because NQC uses the LEGO firmware, I don't think you (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Voltage generator
 
In article <Pine.GSO.3.96.99012....uen.org>, jeff <jeff@uen.org> writes (...) Wait for a calm day and mount it 3 ft above a car, or on the front of a bike with a speedometer. Make several runs in opposite directions at constant speed and take the (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Dacta in Canada? (Was Re: Differentials also available from LegoDacta)
 
The catalog from Spectrum that I have seen has all the Technic related Dacta Service Packs. (...) of (...) I can clear up the "unlikely" scenario that you mentioned. if you tell me what you are looking for, I will just look in the catalog and tell (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Voltage generator/Anemometer
 
In article <Pine.GSO.3.96.99012....uen.org>, jeff <jeff@uen.org> writes (...) Measuring the voltage would be more accurate. (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Dacta in Canada? (Was Re: Differentials also available from LegoDacta)
 
(...) The most recent S@H catalog for Canada was over 50 pages, and more than half of the sets listed were new. Granted, they use large flashy layouts, but would you really want to have a lego catalog in the style of Digi-Key (who can put 450 (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Voltage generator
 
(...) I figure it would take quite a gale to turn over the gear motor with any degree of accuracy, but you might be able to rig something with the rotation sensor and a model airplane prop. Daniel "Dan'l" Miller Senior, School of Aeronautics and (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Sensor monitoring
 
(...) I think the sensors are read every 3ms and the value stored somewhere. I don't think they are read just when you ask for them in software. You get the last value read. I base this on the way the rotation sensor and some of the sensor modes (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Rover (was Voltage Generator)
 
List, I just sent the message below to Linc and not to the whole list as it may be marginal on the Topic issue. Ben has asked about it too and others may. So I'm sending this now. I do still talk about Lego in this but further discussion may be too (...) (28 years ago, 20-Jan-99, to lugnet.robotics)
 
  Re: Voltage generator
 
Daniel, Peter Hesketh posted a similar suggestion, and yes the motor may be too firm for the job. I'll play around and do some testing, this week or as I can get time. Then I'll post the results. My goal is to end up with a pure Lego anemometer or (...) (28 years ago, 20-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR