Subject:
|
Re: RCX not listening to IR remote
|
Newsgroups:
|
lugnet.robotics
|
Date:
|
Mon, 26 Oct 2009 13:42:41 GMT
|
Original-From:
|
J Bickhard <jbickhard@gmailSTOPSPAM.com>
|
Viewed:
|
15735 times
|
| |
|
|
Firstly, do you have the firmware on the RCX in question? If the
screen shows 00.00.00 then you should be good (i think). Turn on the
RCX, and start pressing buttons. Connected motors and lights should
start doing "things" repsonding to the commands from the IR remote. If
NOTHING happens at all, then the ir LED must be bad on the RCX. Can
you program it sucessfully with Robolab or similar?
Jake (dats me)
On Mon, Oct 26, 2009 at 8:17 AM, Steve Hassenplug
<steve@teamhassenplug.org> wrote:
>
> Chris,
>
> I don't think the RCX will "listen" to the remote, unless you've
> loaded the firmware. The firmware will need replaced, if the
> batteries have been removed (or have died).
>
> On the RCX, it will show the program number (1-5), and it will also
> show three other digits, IF the firmware is loaded. If only one digit
> shows, the firmware is not loaded.
>
> The firmware would be on the original software CD. If you don't have
> that, it may be on the NQC web site, or possibly the RobotC web site.
>
> Hope that helps.
> Steve
>
> On Sun, Oct 25, 2009 at 11:54 AM, Chris 'Xenon' Hanson
> <lego-robotics@crynwr.com> wrote:
> >
> > I just dug all my old Mindstorms RCX gear out of the closet because my
> > 4-year
> > old son is
> > now ready to play with gears and motors and stuff. Programming is a bit off
> > yet, but he
> > loves the technics parts.
> >
> > I was trying to get the RCX to work with the IR remote (#9738) that I have.
> > As I recall,
> > the A,B,C buttons on the remote can be used to manually drive the outputs and
> > you can
> > launch programs and send events.
> >
> > The remote has good batteries and seems to be putting out IR signals (I can
> > see the IR
> > LED lighting through my camcorder). The RCX seems to work (the program
> > currently in slot
> > #1 runs output A continuously). But, the RCX doesn't seem to pay any
> > attention
> > to the remote.
> >
> > This isn't my original RCX, rather it's a 1.0 model I bought off eBay
> > because
> > mine seems
> > to have died while being stored in the closet.
> >
> > I'm pointing the IR remote at the IR window on the RCX. Can anyone think of
> > anything I'm
> > missing to get the RCX to listen to the remote?
> >
> > Also, anyone want to buy a presumably injured RCX for a few bucks?
> >
> > --
> > Chris 'Xenon' Hanson, omo sanza lettere Xenon AlphaPixel.com
> > PixelSense Landsat processing now available! http://www.alphapixel.com/demos/
> > "There is no Truth. There is only Perception. To Perceive is to Exist." - Xen
>
|
|
Message is in Reply To:
 | | Re: RCX not listening to IR remote
|
| Chris, I don't think the RCX will "listen" to the remote, unless you've loaded the firmware. The firmware will need replaced, if the batteries have been removed (or have died). On the RCX, it will show the program number (1-5), and it will also (...) (15 years ago, 26-Oct-09, to lugnet.robotics)
|
6 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
