 | | Robo Quad - Stage Eight
|
|
Robo Quad - Stage Eight completed (URL) Robo Quad - Stage One notes> (URL) Robo Quad - Stage Two and Three notes> (URL) Robo Quad - Stage Four and Five notes> (URL) Robo Quad - Stage Six notes> (URL) Robo Quad - Stage Seven notes> Robo Quad - Stage (...) (17 years ago, 3-Jun-07, to lugnet.announce, lugnet.technic, lugnet.robotics, lugnet.build.mecha, FTX)
|
| |
| | Re: Reading Datalog
|
|
The only VI I was able to find is at: (URL) is the purpose of the "UploadDatalog(nStart,nEnd)" function? Is there a way for Robolab to passively receive datalogs? The example I found seems to use the RCX in direct mode, but I am not sure as I do not (...) (17 years ago, 3-Jun-07, to lugnet.robotics)
|
| |
| | RE: Reading Datalog
|
|
RobotC RCX firmware is compatible with Robolab and the vast majority of the Ghost API messages. You can get this firmware by installing an evaluation copy of RobotC. If you are using Robolab, then there are a large variety of VIs available for (...) (17 years ago, 2-Jun-07, to lugnet.robotics)
|
| |
| | Reading Datalog
|
|
I am trying to get the Datalog from my RCX to be displayed on my computer. I am using RobotC to upload the datalog using the "UploadDatalog(nStart,nEnd)" function. It is sending the Datalog because I can see the green LED on the IR tower light up. I (...) (17 years ago, 2-Jun-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
(...) If you do support PIC18F8520, then with some changes to the loader one may be able to program VEX controller with Ultimate_PICLAB.which would be great! Guy Ziv (17 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
(...) ...snip (...) Perhaps I'll answer with a short list of projects that we have realized so far: 1.The most complicated thing I've done with Ultimate_PIC -I have to familiarize with that name now- using the 16F628A is a bi-directional half-duplex (...) (17 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
(...) I'll forward this to Laurent. (17 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
"Claude Baumann" <cbaumann@ci.educ.lu> wrote in message news:JIvFwD.5C3@lugnet.com... (...) Exciting stuff! A friend and I have been using the PICKit2 recently for a range of chips including 12f's and 16f's. So far my personal favorite has been the (...) (17 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
(...) Any chance you'll add PIC18F8520 to the supported list of PICs? Guy Ziv (17 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
(...) The PICkit comes with a little PC board with a 16F690 on it. I don't know how that compares to the 16F88, but it does have a synchronous serial port. (17 years ago, 31-May-07, to lugnet.robotics)
|
