To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 24814 (-10)
  Re: mindstorms NXT
 
(...) Actually, the RCX outputs 0's and 1's to power the motors as it is right now. It uses Pulse Width Modulation (PWM). Basically for 1/3 power 1/3 of the pulse is 1 and the other 2/3 is 0. For full power, the signal is all 1. This creates a (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) Speculation: I think we're looking at some sort of i2c-like type interface here, where you'll find continuous power on one of the pairs and the other two pairs being used as some sort of high-speed digital bidirectional full-duplex or (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) If these lines are purely digital communication lines, adding additional motors will be easy via a multiplexor attached to one of the RJ11 output. Building the multiplexor (or any custom sensors) may not be as easy though. It looks like you (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
 
  Re: Mindstorms NXT & Revalation of the MUP
 
(...) Congrats John, Steve and the others for making the grade. ;) Shall we place bets on who the un-named fifth candidate was? Mario? ;) I applied for the NXT test program already. I'm very excited about the NXT capabilities. I tried creating a (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) Or they are far enough apart or in a difficult arrangement so that a mechanical link is impractical. (eg: moving WRT each other.) ROSCO (21 years ago, 5-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) So you parallel motors on the same port to do different things? As opposed to using a single motor mechanically coupled to different things? Is this as a result of a single motor not being powerful enough? Or because the two paralleled motors (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
 
  Mindstorms 2.0 and MAC users
 
Hello all, I spend a good deal of time answering questions via email, but this one I was unsure of. Could one of my fellow robotics experts be helpful with this question, many thanks! Q: "I HAVE JUST BOUGHT THE MINDSTORM 2.0 (sorry for the shouting (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
You're right... But if the other dimensions are still within close range of those of a RJ11, I guess roll-your-own connectors can 't be that hard... Regards, Simon ----- Original Message ----- From: "Philippe Hurbain" (...) (21 years ago, 5-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) Hope its possible to create an I2C port using the sensor ports. Its a shame they didnt create an I2C port for daisychaining sensors. Or is the sonar port a I2C port.... Ram (21 years ago, 5-Jan-06, to lugnet.robotics)
 
  Re: mindstorms NXT
 
(...) How would you create a rover-based robot with just three motors? I want to design more complex rovers other than the two-wheeled plus caster designs. Something like the shrimp for instance. The old rcx allows you to connect multiple motors to (...) (21 years ago, 5-Jan-06, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR