To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 2466 (+10)
  Re: LOGO with Mindstorms
 
(...) [SNIP] (...) Sorry I didn't pick up this message earlier; I don't read this list every day, because of being busy, and traffic volumes, and... MIT have written BrickLOGO for the RCX; they are in discussion with LEGO inc about whether they can (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  * OFF TOPIC ** Re: So why build robots out of LEGO in the first place?
 
(...) I find it a little sad that one HAS to clarify obvious witticisms in order to avoid a flame war! Ho Hum... (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  RE: So why build robots out of LEGO in the first place?
 
Just a question, Where an inmature lego follower can find the Lego Purity Commandments? I am a kind of new in this _religion_, but I hardly try not to be a sinner. Thanks for the Light in the Darkness, David (...) -- Did you check the web site (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: BotCode
 
You probably did not have to move the Spirit.OCX as it was already there from an install of the Lego software. Yes, I find BotCode and excellent package with only minor bugs. And yes I paid my $20 by CC and got my package with hours over the (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: 3 sensors = 8 inputs?!
 
(...) Unless you add a bit of electronics to multiplex your sensors, use the existing three digital inputs as a mini parallel port, design a simple communications protocol and send the sensor statuses from the module to the RCX using the protocol. A (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: 3 sensors = 8 inputs?!
 
(...) The way the inputs work does not allow hooking something up to two inputs at the same time while still keeping independent use of the inputs. You would need to add at least diodes. I assume you want a pure LEGO solution, but LEGO doesn't have (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  2 Motors off one output???
 
I'm sure that this has been covered before, but!!! Has anyone (or can it be done) hooked two motors(i want them to move in the same direction) up to one of the "A", "B", or "C" outputs. Clay Aucoin Director of Information Technologies, Web Services (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Re: CM in LDraw
 
(...) Answering my own post: I was told L3P ((URL) can make the edges disappear when rendered with POV-Ray ((URL) trick is to put the DAT file into the PARTS directory. Laurentino Martins *<||:-) [mailto:lau@mail.telepac.pt] [(URL) you check the web (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  Help With Programming
 
I am looking for help in programming the RCX using Visual Basic 5.0. I can issue immediate commands successfully, ie turn a motor on or off, however I can not get programs to download into memory. Programs will download successfully into memory (...) (28 years ago, 7-Jan-99, to lugnet.robotics)
 
  legOS help needed
 
I have downloaded cygwin32 and the binaries that were precompiled. I have also compiled Markus's sample programs and the firmdl.c file distributed with legOS. However, when I try to run firmdl, it says that it can't find the srec file (e.g. firmdl (...) (28 years ago, 7-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR