To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 24539 (-10)
  Re: Control Lab Connection help
 
(...) More like 16! (...) Yep. And if all else fails, check the connections. Speaking of cables, I have also used a USB to serial cable connection on a laptop that lacks a serial port, running WinXP. You need a driver for the USB to serial cable, of (...) (21 years ago, 16-Nov-05, to lugnet.robotics)
 
  Re: Basic NQC Problem
 
(...) While the 2nd edition should indeed have some firmware v2 informations (I don't have this edition), the (very useful) chapter 4 covering the new firmware is actually in the Extreme Mindstorms book (ISBN: 1893115844). Philo (21 years ago, 15-Nov-05, to lugnet.robotics)
 
  Re: Basic NQC Problem
 
(...) They first came out with the release of the latest version of the firmware back in March 1999, but they are sadly not well documented, except in one place I know of... (...) ...in Dave's excellent *2nd* edition of this book, he dedicates (...) (21 years ago, 15-Nov-05, to lugnet.robotics)
 
  Re: Control Lab Connection help
 
(...) Well I answered my own question. I had two serial cables given to me by my father and neither worked. The new serial cable I bought did. Now I have the power of eight! In answer to my other questions: Yes, you can use Control Lab interface (...) (21 years ago, 15-Nov-05, to lugnet.robotics)
 
  Re: Basic NQC Problem
 
Thanks to both Brian and Ralph. Your responses were very detailed and helpful. I've played around with the suggested code and learnt a lot. Are events relatively new in NQC? I purchased a second hand copy of David Baum's Definite Guide (1st ed). I (...) (21 years ago, 15-Nov-05, to lugnet.robotics)
 
  RCX Code<-->ROBOLAB?
 
Has anyone written or heard of a program to convert RCX Code into ROBOLAB *.vi's? Can this even be done? I ask because the FLL team I am associated with has ten members. Each member is writing the code for one challenge. After we have all ten (...) (21 years ago, 14-Nov-05, to lugnet.robotics)
 
  Re: Basic NQC Problem
 
(...) There's a couple of ways to fix it. One is as Raplph said - have the first task start up a dedicated second task that does nothing more than look for a touch in a very tight loop. Very roughly, it would work something like this: task (...) (21 years ago, 13-Nov-05, to lugnet.robotics)
 
  Re: Basic NQC Problem
 
(...) Big place to ask your questions here. I'll try to answer it, best i can. (...) You should switch of the motors and StopAllTasks in the check_sensor() task, if the bumper is hit. The main task does not furthermore look like that algorithmic as (...) (21 years ago, 12-Nov-05, to lugnet.robotics)
 
  Control Lab Connection help
 
Greetings, I have been trying program Control Lab using robolab. However, when I go to download all I get is the "Start CLI-1" window with a red 'X' through the reconnect icon. I am using the Control Lab interface start icon. I have tried several (...) (21 years ago, 12-Nov-05, to lugnet.robotics, lugnet.dacta)
 
  Re: Is it possible for a robot to count studs?
 
(...) Yes. The rotation sensor does occasionaly mess up at low rotation speeds, but this issue can be overcome by gearing up the actual rotation to higher speeds, and then dividing it back down in software. Kev (21 years ago, 12-Nov-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR