To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23479 (-10)
  Re: Smack my MOC! - Fly Mech
 
(...) (22 years ago, 9-Feb-05, to lugnet.robotics)
 
  Re: Sending Commands to Spybot from RCX - Question from a Beginner to Comm area.
 
Hi Everybody, I have used SendSpybotMsg and SendSpybotCtrlMessage (of course in connection with resopective set messages) without any problems using BCC 3.3.7.5 and 3.3.7.9. These two commands gives RCX a nice control over spybot. Specially (...) (22 years ago, 8-Feb-05, to lugnet.robotics.spybotics, lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.nqc)
 
  Re: Four rotation sensors on a single sensor port
 
(...) Interesting trick. Thanks for sharing! Philo (22 years ago, 8-Feb-05, to lugnet.robotics)
 
  Four rotation sensors on a single sensor port
 
Hi, that is possible, they count reliably if you move only one at a time and always stop them when their raw-value is the highest (close to 1023, the axis hole is horizontal/vertical). Have fun Jürgen (22 years ago, 8-Feb-05, to lugnet.robotics)
 
  Re: Internals
 
Hi Geoffrey, (...) I know that, but the gears that I mean don't take part in the reduction, the reduction is essentially done only by the axis next to the motor. (...) I was only wondering why they would put two gears on an axis when the second one (...) (22 years ago, 8-Feb-05, to lugnet.robotics)
 
  Re: Internals
 
(...) Indeed, they don't mesh! (...) No, you can't (different tooth size and/or unmatching diameters and/or uncompatible axle and/or different height). (...) Not really easy, but there are plastic clips all around that can be pryed open without too (...) (22 years ago, 8-Feb-05, to lugnet.robotics, lugnet.technic)
 
  Re: How to send commands directly to the RCX?
 
You have to open a port to the Lego Tower. Generally it looks like a file. Here's some Python code I'm using that does it, someone can probably translate to Java: irHnd = CreateFile("\\\\.\\legotower1", GENERIC_READ|GENERIC_WRITE, 0, None, (...) (22 years ago, 8-Feb-05, to lugnet.robotics)
 
  Re: Internals
 
What i guess Jurgen mean is that the two middle gears are meshed in both inner and outter gears, with will block the mechanism because the ratio diference. Unless the bigger gear of the second red gear is useless. Patrick. "Geoffrey Hyde" (...) (22 years ago, 7-Feb-05, to lugnet.robotics, lugnet.technic)
 
  Re: Internals
 
If you look at picture one then picture two, you will notice in the second picture that all but the very last of the four gears actually has a second gear cast onto it, making the three of them essentially two gears and not one. What this (...) (22 years ago, 7-Feb-05, to lugnet.robotics, lugnet.technic)
 
  Re: Internals
 
Hi, (...) from the pictures it seems they would both mesh and block the drive train (which I suppose they don't). Can you turn them aroud to change the gear ratios? Is the motor easy to take apart without breaking it? Jürgen (22 years ago, 7-Feb-05, to lugnet.robotics, lugnet.technic)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR