To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 23384 (-10)
  Re: The Great Ball Contraption
 
(...) It's exactly 2.5. 10 teeth on a gear rack, divided by 4. Steve (22 years ago, 21-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) I'm not exactly sure how many "teeth" = 1 stud, but I know it's not a whole number. So, I've found if you can change the length by 1 or 2 studs, and add a few chain links, you don't need to add a tensioner. Steve (22 years ago, 21-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption
 
(...) I don't know if it fits into the standard or not. I didn't plan on using it as my first device, anyway. I'm going to build a simple large hopper for the previous person's contraption to feed into mine, and then I'll have a feed chute or (...) (22 years ago, 21-Jan-05, to lugnet.robotics, FTX)
 
  Re: Johnny five IS alive - first MOC
 
(...) Hi Bruce Thank you for your feedback. I'll try to make some movies and post them. Steven (22 years ago, 21-Jan-05, to lugnet.robotics, lugnet.build.mecha)
 
  Re: Johnny five IS alive - first MOC
 
(...) --snip-- good idea,I have a lot of hinge plates in my depot. So I will give a try. -------- (...) -- snip -- Yes the 4x plates are really "stressed" turning around the wheels. I think the combination of both, smaller plates and re-arangeing (...) (22 years ago, 21-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)
 
  Re: The Great Ball Contraption 2.0
 
Keep up the great work guys! :) Iain (22 years ago, 21-Jan-05, to lugnet.robotics)
 
  Re: The Great Ball Contraption 2.0
 
In lugnet.robotics, Steve Hassenplug wrote: (snip) (...) (snip) Nevermind the controls, how'd you build the hopper? ;-) I really like your solution, with the rotating arm that unloads it, creating an auto-reset for the hopper. I've been frustrated (...) (22 years ago, 21-Jan-05, to lugnet.robotics, lugnet.trains)
 
  IR Tower Building
 
Dear List, I am without an IR tower for my Mindtsorms kit. I have built two of the schematics here: (URL) of the ones I tried work. I tried the one by John Barnes, and the hardwire cable. I do not know enough about schematics to read the OEM design. (...) (22 years ago, 20-Jan-05, to lugnet.robotics)
 
  Re: Johnny five IS alive - first MOC
 
Hi Stefan, I've seen bits and pieces of this as you've posted them to Brickshelf, but it's great the see Johnny in all his glory. I can't wait to see this completed. I hope that eventually you're able to post movies of him in action. Bruce (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha)
 
  Re: Johnny five IS alive - first MOC
 
(...) Perhaps switching to 2x plates instead of 4x for the tread surfaces would help - this would help to smooth the curve around the wheels, at the cost of almost doubling the number of hinges you would need to add. Otherwise, love this MOC. Great (...) (22 years ago, 20-Jan-05, to lugnet.robotics, lugnet.build.mecha, lugnet.technic)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR