To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 22629 (-10)
  Re: challenge: LEGO copier
 
I think you should start easy, with something like a mosaic copier. (22 years ago, 5-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Except that this is a problem pretty easily solved in code -- it's not necessary that the robot choose the same solution the original builder did; it's only necessary that it choose a solution that works. A robot that copies only continuous (...) (22 years ago, 5-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Ah, hmm, I was expecting it to be a continuous fabric, not a holey one. That would make it harder, and in fact makes it even more important to not confuse neighboring pieces of the same color (otherwise you could lose structural integrity by (...) (22 years ago, 5-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Yes, but not arbitrarily -- there would be some limit in width (Y) and height (Z), in order for the model to fit into the machine. (...) Yes, that's a much harder problem, which is why I was thinking to limit it to a thickness of one in X. (...) (22 years ago, 5-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Okay... I think I understand... so you use some 1xN plates or bricks on the top and the bottom of the whole "picture" to hold it together, and the actual construct built can be any size of width N? Or am I still way out there? >> Mark (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) OK, just to clarify: assume an X-Y-Z space with studs sticking up in the Z direction. You mean a model that's only one stud thick in X, arbitrarily wide in Y, and arbitrarily high in Z? Yes, that would be a much simpler problem than what I was (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) The closest I got to something like that was my half-built Duck Assembly Carousel - a dial automation with 4 positions, which would assemble the body (2x1 inverted slope), beak (2x1 plate), and head (1x1 brick with a hole in it). I didn't have (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
Would the bricks be assembled as a wall one brick thick on its side? Like laying a cinderblock wall on its side then creating a copy? That might be done with an X-Y table arrangement with vice like sides at top and bottom of the bricks so that they (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) There are some clever tricks (diff & ratchet/clutch, muxes) to expand it somewhat for some applications, but in general, yes, a single RCX can drive only three independent pulse-width modulated polarity reversible 9V outputs. -SMQ Shawn (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) No, I meant stuck to each other. (...) That's what I had in mind too. (...) I was assuming the use of a camera, not the LEGO light sensor. But using the light sensor is a clever idea. (...) Here I expose my complete cluelessness with regard to (...) (22 years ago, 4-Aug-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR