 | | how to program the spybot remote
|
|
hi everybody ;-) I use brickCC to program my spybot, do you know how I can program remote' s functions ?? (I talk about the spybot's remote) I' m not a programmer specialist so could you give me few code or a good explanation Thanks to all Chris (...) (20 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
| | Re: how to program the spybot remote
|
|
(...) it's sending (1,2, or 3). All the programming is in the Spybot, where you can change how it responds to different buttons. Steve (20 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
| | Re: how to program the spybot remote
|
|
(...) Hi Steve :-) OK, does it means "spybot" listen remote as it was another spybot ?? using exactly same communication functions ? how can you change remote ID ?? do you have a link where I can find further informations about spy communications?? (...) (20 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
| | Re: how to program the spybot remote
|
|
This is not exactly what you are looking for, but I hope it helps! (URL) think you can use the same process, but you will have to learn what code each button on the remote sends. (...) (20 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
| | Re: how to program the spybot remote
|
|
(...) front,button 3: right) and it looks too hard for me... do I have gave to give up ? :-) thanks Chris. (20 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
| | Re: how to program the spybot remote
|
|
(...) don't give up. without any programming, the remote will drive the spybot. button 1 & 4 control the right motor, button 3 & 5 control the left motor. It seems messed up, but that's how it is. If the motors go the wrong way, you can switch the (...) (20 years ago, 3-Jul-04, to lugnet.robotics)
|
| |
| | Re: how to program the spybot remote
|
|
(...) Steve, no doubt you' re the best !! ;-) quite simple !! perfect!! the good thing is that it works even when program runs.... Thanks a lot (hey Steve have you the seen the gyro-bob on my site, the simplest mechanical alternative to legway: (...) (20 years ago, 4-Jul-04, to lugnet.robotics)
|
| |
| | RCX firmware vs hardware
|
|
All, I've got an RCX 1.0, and my son has a 1.5. Is there anything that would cause problems if I loaded 1.5 firmware into a 1.0 RCX? While on the topic, what about 2.0 firmware in a 1.0 RCX? (20 years ago, 6-Jul-04, to lugnet.robotics)
|
| |
| | Re: RCX firmware vs hardware
|
|
Hi, there is no problem! ;-) I have also an "old" rcx1.0 with a mindstorm 1.5 kit. some weeks ago I have to build the 2.0 kit with the rcx1.5 (one reason is, I needed an usb tower). So I update both rcx withe the newest firmware from LEGOs website (...) (20 years ago, 6-Jul-04, to lugnet.robotics)
|
| |
| | Re: RCX firmware vs hardware
|
|
(...) No, that won't cause any problems. The software versions are all interchangable between the RCXs, so you can use 1.0, 1.5 or 2.0 software/firmware on 1.0, 1.5 or 2.0 RCXs. I have both 1.0 and 2.0 RCXs, and I use the same firmware on both. (...) (20 years ago, 6-Jul-04, to lugnet.robotics)
|
| |
| | Re: RCX firmware vs hardware
|
|
(...) No problem - all versions of firmware work with all versions of RCX. (...) Also no problem. ---...--- Steve Baker ---...--- HomeEmail: <sjbaker1@airmail.net> WorkEmail: <sjbaker@link.com> HomePage : (URL) : (4 URLs) GEEK CODE BLOCK----- GCS (...) (20 years ago, 6-Jul-04, to lugnet.robotics)
|
