 | | Re: (long) Rotation Sensor from "Extreme Creatures" Fiber Optics
|
|
(...) Here are some ideas Maurice Hilarius sent me on the subject. I hope he doesn't mind my reposting them. "1) You attach a smaller wheel on a shaft which is part of the drivetrain. This wheel rotates on the shaft, but with a small amount of (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: (long) Rotation Sensor from "Extreme Creatures" Fiber Optics
|
|
(...) You could make a paper disc that has a radial pattern of 3 repeating colors that the light sensor can distinguish... for example: red, blue, white, red, blue, white... Then by watching the pattern of colors that go by the light sensor, the (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: More input
|
|
Paul Haas found the problem with the URL, but I don't see it posted here. The period on the end of the URL makes it not work. Try this: (URL) Clemens wrote in message <4.1.19981229083143....wc.edu>... (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor input mux calculations
|
|
(...) Here is my understanding of the circuit: AVcc | Rp 10k | A/D input ---...---+---...--- | | | | | | S0 S1 S2 S3 Rc | | | | | R0 R1 R2 R3 | | | | | GND +----+----+----+---- GND Where Rp is the pullup resistor and Rc is the impedence of the (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Extra sensors available in UK
|
|
(...) Legoland Windsor, pah. I went up in mid november, they hadn't a clue. Didn't know when (or even if) sensors would be available. Mind you they hadn't even heard of service packs. Brian Weeks -- Did you check the web site first?: (URL) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor input mux calculations
|
|
I've been looking at the multiple sensor input problem... wouldn't it be simpler to use a series resistor network, rather than parallel, something like this: --|--[ 10 ohm ]--|--[ 20 ohm ]--|--[ 40 ohm ]--|--[ 80 ohm ]--|-- | | | | | (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor input mux calculations
|
|
Yes, I was looking at Forrest Mims' Mini-Notebooks (Sensors) and saw the circuit you just described in there. I would use bigger values for the resistors, but I guess it doesn't matter. The software would be the same. In fact, the only thing that (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Extra sensors available in UK
|
|
(...) one end) and if you know the numbers of the parts then they have them! I of course didn't have the numbers, but the staff were very helpful and did find an angle sensor for me. Philip (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Newbee
|
|
Hi everybody, I just got a MindStorm Kit and I am very excited to see all the progress with hacking and developing hardware and software to extend the capibilities of the RCX. Quick question, can you get this list in Digest form? I know alot of (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Spririt.ocx / Cybermaster
|
|
Hello I have tried to program Cybermaster with Visual Basic and Spirit.ocx. I downloaded getstart.zip but it doesn't work. I cant find file "firm0309.lgo". System is alive and tower tries to download prorgram but cybermaster does not receive (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Newbie
|
|
I am trying to find out what CyberMaster is and where to get it? Can anyone help???...??? Thank You, Clay Aucoin, caucoin@cruiseshoppes.com Information Technologies Director, Web Services Division Cruise & Vacation Shoppes America (URL) 375-0199 x22 (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Lego Mindstorms on Mac using Virtual PC?
|
|
I'm new to this list, so forgive me if this has been discussed before. Has anyone managed to get the Lego Mindstorms software/hardware to work on a Mac using Virtual PC? It seems this should be possible, but the cables I currently have to convert (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | RE: Lego Mindstorms on Mac using Virtual PC?
|
|
One thing that might be hampering you is the cabling. The cable that comes with the Mindstorms kit is a null modem cable in the sense that the RX and TX lines are swapped. (Hense the two female connectors). I haven't checked to see if any of the (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor input mux calculations
|
|
(...) Thanks, I didn't think of that. Since it is a linear function to convert the measured resistance to the switch values, this is much faster and also has better spacing between the values. Using 300, 600, 1.2k, 2.4k, and 4.8k ohm resistors, you (...) (28 years ago, 29-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Spririt.ocx / Cybermaster
|
|
(...) CyberMaster don't have firmware in RAM, only RCX does. That's why you don't have the file. Probably the example is only for RCX users... :-( (...) Here's some WEB sites you may want to check about SPIRIT.OCX programming: LEGO SPIRIT.OCX (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Help with my IR tower
|
|
(...) We just got a set for Christmas and have encountered the same problem. It worked like a champ for several hours then suddenly wouldn't download. I've tried fresh batteries, & an AC power supply. Wiping out the firmware and re-downloading (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Newbee
|
|
You should probably get off the lego-robotics e-mail list and use the Lugnet.Robotics news group to see the messages. This allows you to see threads and ignore stuff you don't care about. All the messages are copied back and forth to both groups so (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor input mux calculations
|
|
The lego touch sensors are not simple on/off switches like you guys show. There is at least 500 ohms in series with them when they are closed. They also seem to be slightly touch sensitive. A light touch will read 1.5K while a hard push is close to (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor input mux calculations
|
|
I'm not talking about using the touch switches. I would make my own switches - probably whiskers - but who knows. The advantage of A/D input is that instead of having two possible states, you have, in this case 1024. Using that fact you can make (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor input mux calculations
|
|
Sinse it has been real quite at work, I did some designing and came up with what I think would be a solution. Using Sensor ports A & B, these could be tied to sense the channel select lines of a Analog Multiplexer. The C port would be connected to (...) (28 years ago, 30-Dec-98, to lugnet.robotics)
|