To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 1831 (+10)
  Re: Mindstorms CD and Soft Windows
 
(...) It seames to be not possible to use these emulators. I've tried them all and is doesn't work. Though the software will run, the hardware won't. There are two options: use Robolab from pitsco-dacta or use Not Quite C from Dave Baum (you can (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
I use epoxy to glue on assorted pieces where I need them. If you use enough epoxy to fill the space completely, you can snap off the piece and then you have a workable Lego bump impression. What I have found with epoxy is that the epoxy holds just (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Voltage or resistance
 
After experimenting with various photo sensors, it appears that resistance is what is measured. Solar cells produce no change in readings, but CdS photo resisters do. I managed to hook up a BASIC STAMP (a small microcomputer by Parallax) to one of (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  The Bed Mill
 
I have posted some pictures of my latest mill at (URL) I will post a QuickTime movie when I complete the program and make a real cut. Bob (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: Voltage or resistance
 
I'm joining this thread a little late, so sorry if any of this has already been stated... For "passive" sensors, the RCX measures a voltage level, but since there's a pullup you may not get what you expect. If memory serves, the RCX ADC uses a 5.0V (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  More input
 
After realizing that the input ports read resistance, I had an idea. Suppose that I used a network of switches and parallel resisters to differentiate between switches? Here's the circuit I have in mind: gnd-----+--[22k]------ switch --+ A | | (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  (no subject)
 
After reading Dave's commentary on the RCX's ADC system, I did a few more test's, and found that I could easily predict the value that the RCX would produce for a given resistor. Just use the voltage divider formula - V=R2 / (10,000 + R2) and (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  Mindstorms CD and Soft Windows
 
I have tried Virtual PC running Windows 95 on my G3 Mac and it doesn't quite work. The software itself runs (albeit with a bit of stuttering on the audio). The problem is the connection to the IR tower. The software doesn't recognize that the tower (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  BotCode
 
I am impressed with the amount of work done with RCX and alternate systems for coding and control. I suppose this is old news to most of you but BotCode is a very nice package for those that want to ditch the Lego interface. (URL) Clemens, Associate (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  Re: Sensor ideas
 
(...) I have thought of a simple level sensor that would use light sensors, a ring pipe, and a ball bearing. Drill holes through the ring, aligned like spokes. Place light sensors on the outside of the ring, facing in. Set the ring like a wheel, and (...) (28 years ago, 28-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR