To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 1621 (+10)
  RE: Limited number of MindStorms??
 
The Wall Street Journal says Lego will sell 80,000 by years end and they still can't meet the global demand for these things. Their marketing folks thought they'd only sell 12,000 the first year. Guess they didn't count on the over 30 crowd still (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Limited number of MindStorms??
 
(...) It ain't so. That's all they planned to make by the end of this year. (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  All-around-the-robot bump detection
 
For those of you with LEGO pneumatics, I've got a question. There seems to be a need for an all-around-the-robot bump detector. Would this work? Wrap soft rubber tubing around the robot, seal one end of the tube, and connect the other to a pneumatic (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
(...) Nice idea, just one problem though... It gives you no idea as to the direction of the collision so the robot would need some other means of locating the cause of the collision and taking remedial action. Still, if you can solve that problem... (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
The tubing is such a small diameter that I think it would take a large surface of contact for enough air to be displaced to move a pneumatic cylinder. Maybe with not-Lego(tm) tubing that was, maybe 1/4 to 1/2 inch [6.35 to 12.7 mm :P ] in radius (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Oh yeah, that too. :) Jeremy Morton a-jeremm@microsoft.com -----Original Message----- From: Fred Read [mailto:fred@corp.ne...om.net.uk] Sent: Friday, December 18, 1998 6:10 AM To: lego-robotics@crynwr.com Subject: Re: All-around-the-robot bump (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
(...) I haven't actually tried this, but I can hardly imagine that the pressure generated from just squeezing one small part of the tube is sufficient to extend a cylinder and press a touch sensor. The pressure generated will probably just "vanish" (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Hmmmmm, It's morning and I haven't had coffee yet so bear this in mind but it seems to me that this is a) a fairly cool scheme for post collision detection, and b)expandable to support direction detection through the use of 4 sensors. Imagine that (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
If you have three sections and overlap them correctly, you can distinguish six different directions of contact. You wouldn't have to multiplex the touch sensors if you didn't need any more inputs, but you could multiplex them onto one input if you (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Jeremy makes a very good point ! :) You should be able to get away with 3 (in theory). I think this "bladder" idea might work better as you could have more air displaced (assuming you hit the obstacle with any kind of speed <G> ). me Andrew Phelps (...) (28 years ago, 18-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR