 | | Re: Where is this part?
|
|
I also had this prob. |I think I heard that the RCX1.0 came with RIS 1.5 though not sure. |This part is in some of the convertible models eg 8252 police buggy |Or a substitute can be made as shown on the following web page = | (URL) |For the (...) (25 years ago, 29-Jan-01, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
| | can i use macromedia flash or director with lego ?
|
|
hi group can i use macromedia flash or director with lego ? DR Patel (25 years ago, 29-Jan-01, to lugnet.robotics)
|
| |
| | Searching for alternatives
|
|
Hi, my question is as follow: The RCX´s main components are the CPU and the i/o interfaces. Do you know of someone working to make a common computer ( using linux) with some hardware for i/o than works like the RCX? I would like to learn more about (...) (25 years ago, 6-Sep-99, to lugnet.robotics)
|
| |
| | Re: LEGO Solar Cell (Was 'Re: New Pitsco Catalog')
|
|
Ram, I shut down marsrobot. The new URL for that robot is: (...) (25 years ago, 29-Jan-01, to lugnet.robotics)
|
| |
| | Re: LEGO Solar Cell (Was 'Re: New Pitsco Catalog')
|
|
Actually, it is capable of driving only the geared 9V motor, but it runs really slowly (that is, not in full power). Check out the following site that uses the RCX and the solar cell on a mobile robot with videos : (URL) Original Message ----- From: (...) (25 years ago, 29-Jan-01, to lugnet.robotics)
|
| |
| | Re: Sensors
|
|
Mail-Thuis <lego-robotics@crynwr.com> wrote in message news:4.3.2.7.2.20010...kom.net... (...) No it is not correct. All three ports are equal. (...) use (...) Yes. Visit (URL) for a lot of information on RCX sensors. (25 years ago, 29-Jan-01, to lugnet.robotics)
|
| |
| | Sensors
|
|
Hi, I have a RCX 1.5 and would like to have some information. 1) Is it correct that only port 2 can be use for the light sensor ? 2) And only ports 1 and 3 for the touch-sensors ? Can I use microswitches and some resistors to make an array which i (...) (25 years ago, 28-Jan-01, to lugnet.robotics)
|
| |
| | Re: Two more for the wish list
|
|
A few months ago I built a model of two synchronized metering pumps, one for nitro-goo and one for glycerine-goo. The idea was to have both pumps synchronized. I did it with a differential and a rotation sensor to mark the difference and a (...) (25 years ago, 28-Jan-01, to lugnet.robotics)
|
| |
| | Re: Two more for the wish list
|
|
(...) Yes - but if you've been following the discussions about dropped counts, you'll know that the standard rotation sensor is pretty inaccurate when you set it up like that. It likes nice *fast* rotation rates. (25 years ago, 28-Jan-01, to lugnet.robotics)
|
| |
| | Re: Two more for the wish list
|
|
Matthias, this is easy to do without a new part. You use a normal differential, put one shaft in one side, the other shaft (but reversed) in the other and connect the rotation sensor to the output. You get a positive count if the right wheel is (...) (25 years ago, 28-Jan-01, to lugnet.robotics)
|
