 | | adder-subtractor
|
|
I have a new adder-subtractor chassis. will post the page soon. should be at odin.prohosting.com/...ad-sub.htm but things are not going as well as they should tonight. bearing that in mind, this design is pretty slimlined and all gears are on one (...) (25 years ago, 16-Jan-01, to lugnet.robotics)
|
| |
| | Re: News sensors and the RDS
|
|
(...) In passive mode using NQC yes. It's RAW format and you have to make the conversion but it works ok. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 16-Jan-01, to lugnet.robotics)
|
| |
| | Check LEGO set form Mobile Phone
|
|
When you buy LEGO set in store or on eBay, would you want to check the official prices and pieces and so on? You can check it from your mobile phone from today, open page at (URL) got it! Zhengrong (25 years ago, 16-Jan-01, to lugnet.trains, lugnet.general, lugnet.lego, lugnet.robotics, lugnet.technic)
|
| |
| | Re: News sensors and the RDS
|
|
"Dean Husby" <nntp@akasa.bc.ca> wrote in message news:3A63CA50.A73758...a.bc.ca... (...) Really? Have you personally verified this is the case, that the light sensor works on a Scout? (25 years ago, 16-Jan-01, to lugnet.robotics)
|
| |
| | Re: I ordered a 1.5 and was sent a 1.0 Good or Bad?
|
|
(...) Hmmm - they told me it would cost $25. (25 years ago, 16-Jan-01, to lugnet.robotics)
|
| |
| | Re: News sensors and the RDS
|
|
(...) Just the touch and Temp sensor I'm afraid. The light Sensor will work as a passive. (ie no red light). The Rotation sensor won't work at all. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 16-Jan-01, to lugnet.robotics)
|
| |
| | News sensors and the RDS
|
|
i am thinking of buying the RDS faitly soon. Do the other sensors lego sells work with the RDS. Thanks Mike out (25 years ago, 16-Jan-01, to lugnet.robotics)
|
| |
| | Re: I ordered a 1.5 and was sent a 1.0 Good or Bad?
|
|
Well, you were lucky. I contacted Lego at the number you gave me and tried to see if they would send me an upgrade as well. They will, but for $25 US ($40 Cdn). Bummer. It's the second time this week. Matthias Jetleb VA3-MWJ (25 years ago, 16-Jan-01, to lugnet.robotics)
|
| |
| | Re: Motor mis-match.
|
|
Why not eliminate the vagueness of RCX's output circuitry altogether by running the motors from a stabilized bench supply set to 9.000 volts. That's is what I did when I characterized all my motors. I measured the rpm and wrote it on the bottom of (...) (25 years ago, 15-Jan-01, to lugnet.robotics)
|
| |
| | Re: Motor mis-match.
|
|
I did it both ways, and got the same results(the order, not in exact speed). I think that the motors are 'tuned' in some way, because random error cannot occur 100% of the time. All motors went slower with the cable turned or the RCX on 'Reverse', (...) (25 years ago, 15-Jan-01, to lugnet.robotics)
|
