To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *936 (+10)
  Re: building a bot
 
From your post it seems that only one battery was used. It is best to have the motor(s) running from a separate battery. Apropriate capacitors for RF noise and large start up currents should be considered. Have fun! (...) Peter (...) ---...--- Ed (...) (30 years ago, 12-Nov-96, to lugnet.robotics.handyboard)
 
  R/C cars as robot chassis
 
Here is a rule of thumb to keep handy when converting R/C cars to robots; o If the R/C car used either NiCd batteries, or it had a NiCd battery pack, the motors will draw too much current for the Handyboard. This is strictly true of any controller (...) (30 years ago, 12-Nov-96, to lugnet.robotics.handyboard)
 
  Pyroelectric Detectors
 
I'd like to incorporate a pryroelectric IR detector into my robot design. "Mobile Robots" has some detail on sensors, but I'd like to keep it cheap. I have an out-of-service Heath/Zenith motion detector lying about - is the sensor within similar to (...) (30 years ago, 12-Nov-96, to lugnet.robotics.handyboard)
 
  Servo_a5
 
Hi, I'm using IC v3.1 beta 4. When I try to load the servo_a5.icb and the servo_a7.icb that I downloaded from the handyboard web page I get the following error: Fatal internal error: Illegal line in .s19 file And then it completely kicks out of IC. (...) (30 years ago, 12-Nov-96, to lugnet.robotics.handyboard)
 
  Re: Servo_a5
 
Maria, Can you follow the instructions for prepping ICB files at (URL) let us know if that solves the problem? I had been told that this problem was solved in the 3.1 versions of IC, but perhaps not. Thank you, Fred In your message you said: (...) (30 years ago, 13-Nov-96, to lugnet.robotics.handyboard)
 
  Re: Servo_a5 (fwd)
 
Hi. I had to remove the CTRL-M's from the file. After I did that it loaded into IC no problem. So the MS-DOS v3.1 beta 4 of IC doesn't handle them. But I came across another problem. For the C wrapper code for the servo_a5 routines I just modified (...) (30 years ago, 13-Nov-96, to lugnet.robotics.handyboard)
 
  Re: Servo_a5 (fwd)
 
(...) OK. Thanks for letting us know. I have updated the FAQ to reflect your observation. (...) Can you try -not- loading your modified servo.c and see if you can get the A5 servo to work? Make sure neither servo.c nor servo.icb is loaded, and then (...) (30 years ago, 13-Nov-96, to lugnet.robotics.handyboard)
 
  Downloading pcode_hb.s19
 
Hi everybody, I have got a problem when trying to download the config register, with the two ways I know: 1/ HBDL for WIN begins to download it but befire the end, it stops and writes: "Bad config register (0x0D), try again". 2/ I lunch "dlm (...) (30 years ago, 14-Nov-96, to lugnet.robotics.handyboard)
 
  Strange...
 
Hello, This is my second message for today, for those who are sleeping... By the way, it's 2 PM in my little country, and today is a good, but strange day! I explain: This morning (for me), I send you a mail because I could not load pcode_hb.s19 I (...) (30 years ago, 14-Nov-96, to lugnet.robotics.handyboard)
 
  Re: Downloading pcode_hb.s19
 
Assuming you have the A1 version of the 6811 (and not the E1), try using the DL.EXE that is provided with the freeware DOS package. -Fred (...) (30 years ago, 14-Nov-96, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR