 | | Re: Robotics sub-groups
|
|
I would like to see at least one of these. It seems that there are several legOS-related projects ongoing and I'm sure people would like to avoid duplicating work (egcs-1.1.1 patches, libgcc.a, etc.). legOS is at the point in its development where (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Motor power?
|
|
=>From: Dan McCabe <danm@seanet.com> =>... =>When I set the motor power (both in RIS and nqc), I expected the speed =>of the motor to be proportional to the power setting (i.e., higher power =>setting makes motor turn faster and vice versa). (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: gleason research experiences?
|
|
Dear Mr. Puchol, Your order was shipped today via UPS Red, and you should have it tomorrow morning. Please be aware that our policy (as stated on our web site) is to ship orders the business day after they are received. Thank you, Wanda Gleason (...) (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Using the Motor as a Tachometer
|
|
I don't know if someone else has already written about this, if so, sorry about being repetetive. I was reading about hooking up 2 motors A + B and arriving at a dynometer arrangement. ie. Turning A causes B to rotate. I tried this, but also hooked (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Motor power?
|
|
The firmware does do PWM. One reason you aren't seeing much difference is that the motor has an internal flywheel. When the pulse is "on", the motor revs up to speed, then this speed is maintained by the flywheel during the "off" pulse. If you put a (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Motor power?
|
|
I have a tracked bot and I can notice the difference in speed when I set the motors to 1 or 4 or 8. John A. Donaldson (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: RCX IR Messages & Universal Remotes
|
|
Ben, I've been trying to use my Palm III with OmniRemote to send messages to the RCX but so far with out success. What was the process you used to train your buttons? What I am doing is using nqc to send a message through the IR tower which I try (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
|
| |
 | | Easy communication between HBs
|
|
After struggling with it for many hours I found an alternative to Randy's serialio.c serial communication which I couldn't get working. So I used the Pa7_9600 Baud Serial output from unknown origin (Fred?) ((URL) ial.html). I cut a standard RJ11 (...) (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | A-S -> Adaptive Transmission (long)
|
|
My own incarnation of the much discussed A-S transmission uses a single differential and relies upon software to synchronize two independent drives. I term my gearing and software system an Adaptive Drive, since it continuously monitors differential (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sonar and RF Modem questions
|
|
I've been looking into this also. I purchased the Parallax RF module, which is very simple to use. However, it seems to provide a transparent RS232 interface, more is needed than this, or at least some data buffering. Linx technologies provides a (...) (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|