 | | Re: shaft encoders for a track drive
|
|
Steve Wall wrote: <snip> (...) I've had good results using Hall effect magnetic sensors. I found some 0.1" dia. disk magnets at the hobby shop and embedded them into the holes in some Lego Technic pulley wheels. It's true that only about three (...) (28 years ago, 16-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) You can try: (URL) for a UK version of the supplementary catalogue. I do have an international version too, but it doesn't cover USA. Personally, I would recommend some pneumatics and some of the cannons from the competition sets (for fun). -- (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | S19 disassembler
|
|
Will someone please point me to an S19 disassember TIA, - - - Nick - - - (28 years ago, 16-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Serial Communication between HBs HELP!!! (Again)
|
|
Hi, I am trying to get communication working between two HBs via the RJ11 serial port. I read the FAQ on the HB web site and I have the right cable. On the trans. HB the power LED blinks which indicates it is transmitting. Also whenever I turn on (...) (28 years ago, 16-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) I purchased the RIS and the Robosports expansion kit, and then ordered the following to fill it out: Lego Dacta 800/362-4308 ===...=== 2x N979891 9V Angle Sensor 2x N779945 Differentials 2x N779932 Black Plates 2x N779876 Large Turntables 2x (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | preliminary legOS API documentation
|
|
Hello, legOS API documentation is in the works. The documentation generator I intend to use, doxygen, supports HTML, LaTeX and manpage generation from javadoc and QT style comments. I've made a preliminary version of the resulting documentation (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: More Outputs for the RCX
|
|
Hi John, I have a mecanical version of this on my website, with pictures. CU Bert Visit my site on Lego, Robot's and Visual Basic at (URL) bericht----- Van: John Brubaker <photoman@novagate.com> Aan: lego-robotics@crynwr.com (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) Hmm, just been thinking about this. You could have a shaft that was free to move back and forth along it axis. On the end of this you would have a series of N spokes. Each spoke ends with a free to move wheel (the axis of the wheel is arranged (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: More Outputs for the RCX
|
|
Bert - Yes, this is what I had in mind, only I would like to implement an electronic version using small relays. Thanks for the the excellent tips and resources on your Web site! I looked at your Visual Basic information when I was getting started (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | gleason research experiences?
|
|
hi i was wondering if anyone has experience ordering miniboards from gleason research. i find it odd that they do not reply to email or phone or messages for an urgent order. did we make a mistake ordering from them? any recommendations? (28 years ago, 16-Feb-99, to lugnet.robotics.handyboard)
|