To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *9236 (+10)
  Re: Expansion board questions
 
Hi Duncan, I would like to have a copy of your hbtest.c to test the expansion board. If you could post it I bet a lot of us would use it to test. Thanks in advance Terry G. ---...--- (...) doesn't (...) which (...) the (...) the (...) height (...) I (...) (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
 
  Re: Expansion board questions
 
(...) Terry, I will send you the code. I sent it to Fred for the website but haven't heard back. I'm reluctant to post it to the list, but I will mail it to anyone who asks... Best, Duncan (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
 
  Sensors
 
I am gathering parts to make sensors and was wondering if anyone has a good source for small microswitches ( for tuch sensors) and also LED lights 9 to 12 volt. Thanks in Advance Jim Clark ---...--- This message was sent from Bess.Net, a filtered (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Expansion board test routine
 
Hello all, Well here it is, for what it's worth. The functions are pretty obvious, it works just like the original hbtest.c that Fred wrote. To try servos other than #5, you'll have to edit the line: servo5=(16*knob()); In the test_servo() routine. (...) (28 years ago, 15-Feb-99, to lugnet.robotics.handyboard)
 
  Re: Sensors
 
I found every thing I needed as far as the light sensors at Radio Shack. I don't know where you're located, but here in California, Fry's Electronics is the place to go. You can get everything you need from parts, boards, and the junk food to eat (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Re: Sensors
 
The best source I can think of is the old family VCR. It has MANY momentary switches and probably 5 or more LED's in the front panel. There are two infra-red photosensors and a two sided infra-red LED on a post in the tape drive area. Good Luck! :-> (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Re: Robotics sub-groups
 
(...) I agree with your gut- go with one group at first. I suspect it will be a relatively quiet group anyway. Dave (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
 
  Re: RCX Assembler programing
 
Actually, you'll need a Hitachi H8 assembler. I think there is reasonable support for Hitachi H8 in the gnu assembler. Unfortunately I can't remember if the assembler is in its own distribution package, or part of binutils. Dave (...) reply to: (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Re: Sensors
 
(...) I found a GREAT source for small switches is inside an old mouse (um, computer mouse, NOT the rodent). I took apart several different brands of mice, and while they had different ways to measure movement, they all used the same type of (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
 
  Re: RCX Assembler programing
 
=>From: dbaum@spambgoneenteract.com (Dave Baum) =>... =>Actually, you'll need a Hitachi H8 assembler. I think there is reasonable =>support for Hitachi H8 in the gnu assembler. Unfortunately I can't =>remember if the assembler is in its own (...) (28 years ago, 15-Feb-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR