To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8616 (+10)
  Re: Gear Designs
 
Go to ftp://cherupakha.med...ple/fredm/ and download "artoflego.pdf" This is THE book on lego setups, a little math, and lego gear design, with lots of what he calls "cliches." Most outstanding document! -----Original Message----- From: Frank (...) (28 years ago, 30-Jan-99, to lugnet.robotics)
 
  3D Models of the RCX unit?
 
Hi, if there are good free models available, I'd appreciate it if you mailed them to me. Two different versions - one with colors only, one with textures - would be especially handy. Thanks, Markus. (28 years ago, 30-Jan-99, to lugnet.robotics)
 
  DL with a Mac
 
Fred- Thank you for the new version DLoader MCL. I can now indeed load the P- code. Useing this Mac 6500 Apple talk off-printer port-I am still finding odd things-very odd things. A week back-I replaced the hex inverter, memory chip, & U6. Now-after (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  Earlier DL post
 
Fred- Thank you-it helps when you put the libraries that won't load into the right folder. I shall take up with Newton Labs why the HB won't talk to the HB and says out of date 2.81 code is out of date. Thank you again for all your help. Cappy (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  Re: ** voltage dropping and current limitting**
 
(...) Well, just off the top of my head, when you say "get 16 vac out" how are you determining this, a volt meter set for "Volts AC" or some such? Not, say, an oscilloscope? You will note that almost all meters render "AC Voltage" as the RMS (Root (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  Re: HB Expansion kit
 
---...--- (...) Yes (...) ----6---J2-19 pin ,J19-two 4 pin,J6-4 pin,-one 14 pin for the LCD,-one 4 pin lower r.h. over digital 0,1,2,3. on the hb. All go on the outer edge of the board except J19. Hope this helps, I was also pleased with the kit (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  Mindstorm Mac Patch
 
Has anyone had success using the Mac patches for Mindstorms with an Apple PC compatibility Card? (URL) have a 12" Apple PC Compatibility Card and have tried both patches with no success. I would like to hear from someone who has gotten one to work (...) (28 years ago, 30-Jan-99, to lugnet.robotics)
 
  infrared distance sensor
 
Hi, I've just received a Sharp Digital Infra-Red Ranging System (GP2D02) and I'd like to connect it to the handyboard. The device clocks the data in on a digitial input but requires the clocking pulses to be no longer than 200 microseconds. This (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  Re: HB failure
 
(...) Thanks for your response. When we load the pcode_hb.s19file with the right CONFIG it seems to load properly. We then turn the HB off and back on and try to load the Interactive C. This does not work at the computer says "attempting to linkt to (...) (28 years ago, 30-Jan-99, to lugnet.robotics.handyboard)
 
  NQC Barcode program
 
The following is a program someone made on the mindstorms page. There is an error on line 13 but I can't figure it out. I'm not all that experienced so it may be something simple I don't know. Any way, have a look: //This program will decode a "3 of (...) (28 years ago, 30-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR