To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8371 (+10)
  Re: Ball gear
 
(...) The "ball gear" part is used to transfer rotation momentum to a tilted axle. In the 8880 Supercar (URL) is used to make steering wheel drive. (Actually, it has 4 wheel drive, steer and suspension.) It is also used to make a tilting helicopter (...) (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: batteries port
 
(...) That sounds like too much voltage for the HB. I think I remember reading that the HB runs on up to 12 V max. Check the Handy Board Technical Reference. There are much better ways to run motors that require higher voltages. Try using a separate (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
 
  Re: navigation with compass
 
(...) Richard (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Re: Wirz LMD18200
 
I'm not familiar with the Wirz board, however the board I built used the regular "motor output" of the handyboard with no modification required. The trick was to use an opto-isolator to "recover" the forward and backward logic states. That was done (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
 
  Sound Sensor Mic
 
If you are having trouble finding the crystal microphone used in my sound sensor I've found the earphone from a crystal radio kit works OK. Radio Shack sells a kit like this for about $7. (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Interactive C-OS8 Downloading Problems
 
I have nearly teared my hair out trying to get my HB to to DL on a my OS8 6500 Mac. I though there might be someting wrong with the HB and replaced 5 chips. Today I took my HB over to a friends house who has a Performa 475 and hand had no problems. (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
 
  Re: DATALOG and C
 
Michael Gasperi wrote: The UploadDatalog and SetDatalog are Immediate Commands and (...) What do you mean by this? Do you mean they can't be included in a program running on the RCX? Or can't be included in a program running on the host PC? (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  Analog Ports
 
I have the MTJPRO11 board by Mekatronix as well as the MIT HandyBoard both use the 68HC11A1FN mcu. I am using hacked Sharp GP1U58 'tin can' detectors so that they output analog voltage from 1.5 to 2.5 ( effective proximity range is approximately 4" (...) (28 years ago, 24-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Robolab for the World!
 
(...) No, we sure wouldn't. I mean, all software on all our machines is quite legal, right? I say to you, sir, Poppycock! Jasper (28 years ago, 24-Jan-99, to lugnet.robotics)
 
  RE: DATALOG and C
 
There is no way that the RCX can explicitly start an upload, it has to be requested by the PC. There is no problem however aquiring your goal with messages or variables. The best way I have found to achive your goal is to let the RCX signal to the (...) (28 years ago, 24-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR