To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *7871 (+10)
  RE: simple touch sensor construction
 
If you place the bolts on diagonally opposite corners within the 2 x 2 square, then the connector will work from any orientation: Currently, the web page shows x o o o x o o o But if you do o x o o x o o o (The x's represent the nuts, and the o's (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  RE: simple touch sensor construction
 
> I've been working on constructing a touch sensor from parts of old > devices. I discovered that the micro switches from a MS mouse and a > Logitech mouse are the exact width of the inside dimensions of a 2x Lego > brick. Here are the instructions (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: ng/ml gatewaying
 
(...) Seriously? Okie dokie then, this'll be a snap to fix. Happy day! I'll disable 'From'-header munging for the lugnet.robotics->lego-robotics gateway (leaving it in for now on the other ng/ml gateways). You'll still be able to see real-life names (...) (28 years ago, 14-Jan-99, to lugnet.robotics, lugnet.admin.general)
 
  Pen Mounting Ideas?
 
Greetings! I have completed my "LEG-A-SKETCH", which works great, except for the marker, I use a standard dry-erase marker so it comes of the legos if I mess up :) My problem is that the lines will skip and the marker wont stay straight up and down, (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: TI SN754410
 
(...) If you can't find the TI chip try doubling up on the L293D by piggybacking them on top of each other for added amps. You can use one L293D with an additional L293 on top of it (the 'D' has protection diodes that you MUST have). You may need to (...) (28 years ago, 14-Jan-99, to lugnet.robotics.handyboard)
 
  assembling the pcode
 
hi i've recently modified the pcode.asm file to make the timer interrupt occur at 2KHz, rather than 1KHz. does anyone know how i'm supposed to assemble/compile this pcode.asm file into the pcode_hb.s19 file that will be loaded into the Handyboard? (...) (28 years ago, 14-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Synchro drive in Lego
 
(...) Hi, I'm new here, so if I'm missing something, sorry! Seems what you are describing is just what I'd call a "relay switch". The output signal from the RCX goes to a switch, which switches the external power going to your motors. Seems to me (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Synchro drive in Lego
 
(...) Hrm... how would you manage that? I cannot think of any purely mechanical approach that could do the trick. (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: Pen Mounting Ideas?
 
(...) If you construct a beam with an L-shaped cross section, the pen can rest along the groove in the corner of the L, held with small rubber bands at top and bottom. (...) Try putting the tires on the end of a hinged beam, so that they can provide (...) (28 years ago, 14-Jan-99, to lugnet.robotics)
 
  Re: RCX 2.0 -- ideas.
 
(...) Brett, I have been working on a couple different transmission designs with multiple gear ratios. I am most interested in knowing how you used a RCX motor to shift the motors into the two different drive trains. Does it require any sensors? Any (...) (28 years ago, 14-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR