To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6861 (-10)
  Re: Sensor ideas
 
(...) I have thought of a simple level sensor that would use light sensors, a ring pipe, and a ball bearing. Drill holes through the ring, aligned like spokes. Place light sensors on the outside of the ring, facing in. Set the ring like a wheel, and (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  BotCode
 
I am impressed with the amount of work done with RCX and alternate systems for coding and control. I suppose this is old news to most of you but BotCode is a very nice package for those that want to ditch the Lego interface. (URL) Clemens, Associate (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  Mindstorms CD and Soft Windows
 
I have tried Virtual PC running Windows 95 on my G3 Mac and it doesn't quite work. The software itself runs (albeit with a bit of stuttering on the audio). The problem is the connection to the IR tower. The software doesn't recognize that the tower (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  (no subject)
 
After reading Dave's commentary on the RCX's ADC system, I did a few more test's, and found that I could easily predict the value that the RCX would produce for a given resistor. Just use the voltage divider formula - V=R2 / (10,000 + R2) and (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  More input
 
After realizing that the input ports read resistance, I had an idea. Suppose that I used a network of switches and parallel resisters to differentiate between switches? Here's the circuit I have in mind: gnd-----+--[22k]------ switch --+ A | | (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
 
  Re: Voltage or resistance
 
I'm joining this thread a little late, so sorry if any of this has already been stated... For "passive" sensors, the RCX measures a voltage level, but since there's a pullup you may not get what you expect. If memory serves, the RCX ADC uses a 5.0V (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  The Bed Mill
 
I have posted some pictures of my latest mill at (URL) I will post a QuickTime movie when I complete the program and make a real cut. Bob (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  DC Motor Manufacturers
 
Hello everyone, Has anyone found a good source for DC motors? I am looking for small motors to use as direct drive movement of a small 1.5 LB robot. Any help is greatly appreciated! Bill Denzel Senior Mechatronics Student California Polytechnic (...) (28 years ago, 27-Dec-98, to lugnet.robotics.handyboard)
 
  Voltage or resistance
 
After experimenting with various photo sensors, it appears that resistance is what is measured. Solar cells produce no change in readings, but CdS photo resisters do. I managed to hook up a BASIC STAMP (a small microcomputer by Parallax) to one of (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
 
  Re: R/C Servo to Legos
 
I use epoxy to glue on assorted pieces where I need them. If you use enough epoxy to fill the space completely, you can snap off the piece and then you have a workable Lego bump impression. What I have found with epoxy is that the epoxy holds just (...) (28 years ago, 27-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR