To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6636 (+10)
  Order RCX seperately (new in online catalog)
 
I don't know if anyone has mentioned this yet, but it looks like the RCX is listed as an individual item on the Lego on-line catalog: (URL) havta call S@H and see what it costs. Hopefully, it's cheaper than through Pitsco. (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  Re: Order RCX seperately (new in online catalog)
 
(...) Unfortunately, no sensors. :( (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  dc motor output control???...???
 
hi everyone, i need some help on controling the output voltage of the dc motor ports. the output voltage is 9.6V and i like to know if there is any way to clamp down the voltage to 5V or lesser. i try using a enternal resistor but the output signal (...) (28 years ago, 19-Dec-98, to lugnet.robotics.handyboard)
 
  Re: ROBOLAB in Europe
 
Hallo Werner, the distributor for Lego schools in Germany is Technik-LPE Schulausstattung Postfach 1121 69401 Eberbach Telefon 06271-923410 Telefax 06271-923420 Email mailto:Technik-LPE@t-online.de They mailed to me that they have ROBOLAB in January (...) (28 years ago, 17-Dec-98, to lugnet.robotics)
 
  Re: Lego-animated building instructions
 
Oh god! First Lego Mindstorm, then Cybermaster, now Robolab and The Intelligent House as well! What I & Sam (son) saw in the shop was Lego-animated construction instructions for building this hopping monster thing that jiggered about on the counter, (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  updated my website...finally
 
Hi folks. I've finally added a few Mindstorms creations to the web page at (URL) (28 years ago, 19-Dec-98, to lugnet.build, lugnet.robotics)
 
  New robotics website online
 
Check out www.robotbuilders.com Add a link to your website in the Web Links section. Regards, Mark Williamson (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  Re: a/d range
 
Hi friends! Thank you for the replies about this topic. Now I could get a Reference Manual too... The a/d range is determined by the references given to the VrefH and VrefL pins. But be careful about this: "There should be at least 2.5V between (...) (28 years ago, 20-Dec-98, to lugnet.robotics.handyboard)
 
  Re: All-around-the-robot bump detection
 
to Dennis Parker's point OK so you get this tube wired up to act as a switch. What's the energy drain on your batteries? What are the voltages required to exceed the limit value of the actuator? It sounds more accurate than an air filled tube (...) (28 years ago, 20-Dec-98, to lugnet.robotics)
 
  Re: Vertical Mill
 
Robert Fay writes: > I have posted pictures and a QuickTime movie of my new vertical mill at > (URL) adding all of these to the ``Building'' section of the list web site at (URL) It would be great to know if the model is ``Mindstorms-Pure''. I'm (...) (28 years ago, 20-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR