 | | RE: legOS
|
|
(...) For some Pilot <--> RCX information take a look at (URL) if you haven't yet. This honestly is quite lagging on progress, but I _have_ been working on it in my very limited spare time. Hopefully within a week or two I'll have some much more (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
|
| |
 | | RE: Worm Drive Question
|
|
(...) Sorry I Lost you there, what do you mean by cut Lego? Tim (28 years ago, 25-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Worm Drive Question
|
|
(...) I mean cut threads (like on a screw) into the axel using a thread cutting tool (part of a tap and die set available at most good hardware stores). Check out (URL) near the bottom of the page. (28 years ago, 25-Nov-98, to lugnet.robotics)
|
| |
 | | RE: Worm Drive Question
|
|
(...) As in run an axle through a die to give it a thread, then put nylon bolts on it. Couldn't you just get some threaded rod, and spare your Lego (and avoid heresy :) ? Daniel "Dan'l" Miller Senior, School of Aeronautics and (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
|
| |
 | | Re: legOS
|
|
Has anyone be able to unpack the LegOS file. I have the CYGNUS GCC on my Wintel system. Using GZIP I get this error "Invaled Compressed Data - Format Violation" I would like to try out LegOS and see if it will allow memory storage/retrieval. I have (...) (28 years ago, 24-Nov-98, to lugnet.robotics)
|
| |
 | | Re: legOS
|
|
(...) Hi, You can get legOS at (URL) . There is a note that some people have a problem with the file after downloading. Instead of clicking on the file, right click and select save link. It will save as legOS-0.1.2.tgz . Then run tar -xzf (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Worm Drive Question
|
|
(...) lurk mode off - Yup ... unless you wanted to connect another cross-axle compatable element. I was just curious how well this would work as a substitute as I only had two original LEGO threaded axles from 8094. Heresy? Doesn't everyone have (...) (28 years ago, 24-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Re Sorry
|
|
In article <slrn75mnst.n02.matt...a.bu.edu>, Matthew Miller <lugnet.robotics@lugnet.com> quotes and writes (...) I think that you have hit the nail on the head there. I have read many articles on netiquette, and without exception they _all_ say (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
|
| |
 | | Working automatic transmission!
|
|
I took Dave Forrest's automatic transmission challenge and built a working model out of basic technic. It determines which gear to use strictly based on the load being driven. I put a shock-absorber spring over an axle next to a screw. The screw (...) (28 years ago, 25-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Sharp IR-Distance Sensor GP2D02
|
|
Hi Rajbala, in germany i can get this sensor from "Conrad Electronic". The Sensor is produced from Sharp. It is a very interesting sensor, because it is cheap (ca. 16,00$) It is possible to measure distances between 8-80cm, with a accuracy from (...) (28 years ago, 25-Nov-98, to lugnet.robotics.handyboard)
|