To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5241 (+20)
  MindStorms on NT / trouble posting to the list
 
I'm posting this question on behalf of peterbag@microsoft.com. Please direct replies to that address... Peter asks, Help! I am considering purchasing a MindStorms kit tonight, but I want to make sure it will run under WindowsNT. Has anyone done (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
Alex Wetmore wrote in message <008601be0f2a$01b821...ft.com>... (...) This would give you a good turning radius. However, it would take the bot a long time to turn. (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
Ardjan Besse wrote in message <364c7d42.4532817@lu...et.com>... (...) "Straight" is a relative term. For example, while the alignment might be 0straight, the wheels might not provide the bot with the ability to travel in a straight line. I believe (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) 1) You've been playing too much Carmageddon. 2) Control theory is relatively new (it paces the development of computers). There are quite a few good textbooks available, but a professor is a much greater help. Familiarity with calculus and (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
Daniel Miller wrote in message ... (...) What? (...) This is all fine and well, but I was thinking about something a little less complex. The RCX doesn't have the power to perform image processing and sophisticated feedback control. What I was (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re:
 
Hi everyone, The mistake you make in your calculation is that in your calculation you take the entire 15V for the resistor and this leaves no voltage for charging your NiCad. Do the same thing again and deduct your NiCad voltage from the 15V you (...) (28 years ago, 14-Nov-98, to lugnet.robotics.handyboard)
 
  Cybermaster protocol?
 
Does anybody have information on the basic Cybermaster packet protocol handy? How does it differ from the 55 ff 00 D ~D D ~D C ~C format of the RCX? -Kekoa (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) Believe it or not, I've been working on exactly this problem for the last few days. I built an angle sensor using a 500K potentiometer wired directly to an RCX input port. (Lego's angle sensor doesn't have sufficient angular resolution unless (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Homebrew sensors?
 
(...) So's Michael - he's proposing a notch filter so you get the amplitude at a particular frequency, which may be better for a seeking application. Cheers, Ben. (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) I think making the pendulum longer should cure this... (...) Possibly making it heavier will cure this... Cheers, Ben. (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Homebrew sensors?
 
In article <Pine.GSO.3.96.98111...129.6050E- 100000@expert.cc.purdue.edu>, Daniel Miller <danielmi@expert.cc.purdue.e du> writes (...) Ah. A jet engine expert. It always puzzled me how the hot air knows it is supposed to go out of the hole at the (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Homebrew sensors?
 
does pressure difference make any sense?..:-) Selçuk (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: NiCd Charger
 
Russ: In a message dated 98-11-13 04:48:38 EST, you write: << ... power rating of resistor = 15Volts * 200mA = 3Watts Series resistor needed = 75 Ohms @ 3 Watts. ---...--- ------- The 75 Ohms bit seems reasonable to me but 3Watts must be way to (...) (28 years ago, 14-Nov-98, to lugnet.robotics.handyboard)
 
  Re: moving in a straight line with two motors?
 
---...--- (...) attached. (...) is (...) is (...) sheet (...) I expect that the "motor is shorted" state is achieved by turning on either both high-side drive FET's or both low-side drive FET's, and niether of these combinations would provide a high (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Cybermaster protocol?
 
(...) If I'm not mistaken, Peter Ljungstrand has compiled this information at (URL) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Mindstorms meeting in Boston
 
Hey -- any Boston area people should come to the Construction Site tomorrow (Nov 15) from 7-9 for a Mindstorms show-n-tell/get-together. Details (such as there are) on lugnet in lugnet.loc.us.ma.bos (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  How to receive messages from the CuberMaster unit?
 
I'm currently using Dave Baum's NQC on a Linux system with CyberMaster (thanks to Peter Ljungstrand's adaption), and am very happy with that. However, I often find myself in the position where I want to transfer data from the CyberMaster mobile unit (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) Image processing? Proportional control pushes back proportional to deflection (i.e. it simulates a spring). Derivative control pushes back proportional to rate of deflection (i.e. it simulates dynamic friction). Integral control pushes back (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: moving in a straight line with two motors?
 
(...) Perhaps you're asking too much of them. Try toning down the pendulum; that is, give it some length below the hinge point as well. As long as it's still top-heavy you're still technically an inverted pendulum, and the added mass below the pivot (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
 
  Re: Monitoring household power consumption
 
Hi all, I found an interesting article by Don Lancaster in May 1998 issue of the magazine, Electronics Now. Maxim makes a chip (MAX125) that will convert accurately four channels of analog data to 13 bits accuracy, plus talk about a device for $79 (...) (28 years ago, 14-Nov-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR