To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5191 (-10)
  Re: Tachocount
 
(...) I think we need to think of other applications than cars as well. The tachometer can be useful in a lot of other mechanisms. Suppose we have a 2D plotter set up, and use one motor for the x coordinate and one for the y. That way, tachometers (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Tachocount
 
Do you think a tachometer needs to distinguish direction? Why? Going forward or not, a vehicle _moves_ from one place to the other, so the space moved must always be added, never subtracted. How could you otherwise figure _how_much_distance_ you (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: A spider (legged) RCX robot
 
(...) for moving the legs up and down very thoroughly, but not the rotating of the legs. The first time I saw the article, I thought the model moved by always keeping at least four legs fully extended. I later learned that this was not true, but I (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Multiplexing Input Circuit
 
(...) The setup I was using was bi-directional too, I'm not sure exactly why I was seeing it, but I remember getting a high reading for a non-pressed touch sensor when the next one over (the previous one in the cycle?) was pressed. If I reversed the (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Tachocount
 
(...) I'm sure the motors may be used for other things as well, albeit not as easily as separate motors. (...) But in a program you will always know which way the motors drive, right? So one can possibly maintain a second variable for each motor (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Multiplexing Input Circuit
 
(...) The counter is a CMOS decade counter that has only one output high for each count. There is only one analog switch on at a time. The counter is reset when it hits the value 5 so it jumps back to 0 to start over. The analog switch is (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Connecting two HandyBoards through their serial ports
 
Gads Bill, you are right and my info in the FAQ is dead wrong. I have updated the FAQ with the corrected information. *Thanks a lot* for working this one through. There are few things more annoying than completely wrong documentation (compiler bugs (...) (28 years ago, 12-Nov-98, to lugnet.robotics.handyboard)
 
  Re: Multiplexing Input Circuit
 
(...) Looks good! How about using the third input port to assert the reset line and set the counter back to zero? Is your counter set up as a binary counter? From your diagram it looks like there are times that more than one sensor would be active (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Multiplexing Input Circuit
 
(...) Require it to be clocked every so often, reset if it is held high for a certain length of time. Alternatively, it may be possible to drop the voltage to zero - but that would require a firware change... anyway, I'll look into it out of (...) (28 years ago, 12-Nov-98, to lugnet.robotics)
 
  Re: Connecting two HandyBoards through their serial ports
 
Hello, everyone: Richard Drushel helped me solve the problem that I was having in getting two HandyBoards to communicate through their serial ports by suggesting that I check to be sure that the wiring on the RJ11 cable I was using corresponded to a (...) (28 years ago, 12-Nov-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR