To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4746 (+10)
  Dead HB
 
Hi All, While I was building my sumo robot I managed to short a wire in my HB. I put a wire that was connected to a multimeter and also connected to another part of the robot, into a digital sensor input, sparks came out and it smelt like burnt (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Dead HB
 
Well maybe you should try replacing the HC11 for a start.. These things tend to spoil easily and for no apparent reason.... :( (or is it just bad luck?) That's funny, you shorted out something and it still can download? Maybe you should also change (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)
 
  No stepper motor info in FAQ?
 
Hi all, I just finished searching the FAQ for stepper motor driving tips and found none. :( Anyone know what the most efficient way to connect a stepper motor to the HB? I know that they have these $8ish driver chips...but I've never used one. If (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)
 
  Expansion Board availability?
 
Ok, I found the link to the Expansion board info website...it's all about a beta version. But, there appears to be enough information there for me to build one myself. (is that what everyone's done?) I have never built something from scratch like (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)
 
  Re: data capture
 
Justin, I didn't see anyone reply to your RS232 Question. ALthough I am a newbie to the Handyboard, I have been doing RS232 programming off and on for years. My conclusion is that there have been MANY null modem configurations...but, they seem to be (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)
 
  Re: No stepper motor info in FAQ?
 
(...) HB? (...) Allegro Systems UCN5804B is $3 and change from Newark Electronics. That's not so many $s. It can drive steppers up to 1.25A. The interfacing is easy, datasheet available on-line. Hope this helps, Art (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)
 
  RE: Read A/D converter
 
I didn't look that closely at your program but I have included a routine to read the analog ports that I know works. After assembling and loading the program, you make two c function calls: powerup_ad(); and read_ad(i); where i is the analog port (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)
 
  Lego Mindstorms page
 
Hi all, come visit my page: (URL) (28 years ago, 22-Oct-98, to lugnet.robotics)
 
  Re: Lego Plotter - a few pics.
 
(...) You followed the cardinal rule of web-design: have your content first, before your form. But then you added very nice form. And then you were modest about the result. Perfectionist, in my book: turning out high-quality goods, but worrying the (...) (28 years ago, 22-Oct-98, to lugnet.robotics)
 
  Re: Dead HB
 
Sounds like a lot of it is still up and running if you can download. I'd suggest going through the assembly instructions and performing the tests at the end of each section. You should, thereby, be able to isolate smaller areas that may be fried and (...) (28 years ago, 22-Oct-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR