 | | Re: pbLua GUI ???
|
|
(...) This is starting to look pretty promising as a standard IDE. I will do my part and install Eclipse here and get the instructions updated from Christian's instructions. Once we get a decent IDE the pbLua system may be almost ready for "everyone (...) (17 years ago, 3-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: pbLua GUI ???
|
|
(...) ;-) currently I'm extending Eclipse with simple terminalprogram and pbLuaAPI... With pbLuaAPI-Wrapper(maps pbLua nxt.* to native Lua routines) you can test and run pbLua code at local PC before transfering to NXT... Christian (17 years ago, 3-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: the LEGO CNC-Machine
|
|
i uploaded a little video of the first tests with the x and y axes. check it out here: (URL) trying out wax and soap as cutting materials, i'll report again when i'Ve tested some more :) (17 years ago, 3-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: pbLua GUI ???
|
|
Zitat von Christian Mock <chrimo-@-moccy.xdsnet.de>: (...) pbLua/NXT support there is rather sparse, isn't? Matthias "why don't I do that myself, though?" ---...--- This message was sent using IMP, the Internet Messaging Program. (17 years ago, 3-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: Ooops! NXT Software Comparison correction
|
|
I can further manipulate the numbers for this timing test by using the enhanced standard firmware's support for adjusting a thread's priority. Here's the results when I tweak priorities: W/O LCD LCD Priorities ---...--- 50617 22608 40/5 63211 27375 (...) (17 years ago, 2-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: Ooops! NXT Software Comparison correction
|
|
(...) So if I cheat I can move the I2C transaction out of the actual timing loop (which may be what some other folks are doing, effectively) then with a "read" of the Ultrasonic sensor value in the loop and all sensors and motors attached I get (...) (17 years ago, 2-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: Ooops! NXT Software Comparison correction
|
|
(...) Nearly all of the speed test numbers on Steve's page are wrong. That's because Steve's loop boils down to "how fast can you reliably read the LEGO Ultrasonic Sensor". You can't reliably read a value from that device faster than about once (...) (17 years ago, 2-Sep-07, to lugnet.robotics.nxt)
|
| |
| | Re: the LEGO CNC-Machine
|
|
"daniel" <daniel.formatc.at.gmail.com> wrote in message news:Jnqvwx.p6G@lugnet.com... (...) Right! Program = x+1.005, Y-2.000, F36 (hope it makes it) i have two (...) I had forgotten that you can use a Lego Fiber Optic unit for a rotation sensor. 8 (...) (17 years ago, 2-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: the LEGO CNC-Machine
|
|
(...) by loaded, you mean it carries the workpiece and not the tool? (...) ooh i see now, so that's the anti-backlash gearbox!! awesome, i would never have thought of that. but i don't know if i will be able to integrate that mechanism into my (...) (17 years ago, 2-Sep-07, to lugnet.robotics.rcx)
|
| |
| | Re: I played with fire...
|
|
Well, Philo did it again, Hourrah for him... I bypassed the fuse and the RCX came back to life. Now, will I be carefull enough with my RCX without a fuse or should I replace it ? (17 years ago, 2-Sep-07, to lugnet.robotics.rcx)
|
