To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4696 (+10)
  Updates to MCC - VB Mindstorms application
 
I have posted updates to the latest version of MCC (Mindstorms Control Centre) V 0.2.1 Fixed minor issues related to visual representation of motor controls. See LEGO -> CODE section for downloads of the exe and VB 5 project files. -- Visit my (...) (28 years ago, 18-Oct-98, to lugnet.robotics)
 
  Address locations port d and y0
 
Ok I've had another read of the FAQ, as well as a close look at the schematics for the handyboard and the expansion board. Correct me if I'm wrong, but I think I can use d0-d7 along with Y0 or similar and hook these into a HC374 to get some digital (...) (28 years ago, 18-Oct-98, to lugnet.robotics.handyboard)
 
  NEC V40
 
Sorry to intrude, I would like to check with people of this list if any one have used the NEC V40 ucontroller before. I'm doing a project on this and have problem programming the timer and intrl3. Kind reply to me personally at (...) (28 years ago, 18-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Address locations port d and y0
 
it's in the faq, at (URL) you do is write to 0x4000, 0x5000, 0x6000 depending on whether your latch is attached to Y0, Y2, or Y4 (respectively). e.g., "poke(0x4000, 0xff);" will set all the bits of a latch attached to Y0 to 1. Fred In your message (...) (28 years ago, 18-Oct-98, to lugnet.robotics.handyboard)
 
  Rocker-boogie suspension model
 
Here is a model that incorporates a 6 wheel drive, independent and un-sprung suspension system. This was modeled after the rocker-boogie suspension on Sojourner. As I mention below, this is quick to build and real fun to watch climb across your Lego (...) (28 years ago, 18-Oct-98, to lugnet.build, lugnet.robotics)
 
  Re: Rocker-boogie suspension model
 
(...) office, I think... Can you describe how to set up the motors? It's not clear in the picture, and I don't want to have to dig up LDraw to figure it out. Thanks, -Kekoa (28 years ago, 18-Oct-98, to lugnet.build, lugnet.robotics)
 
  platform choices...
 
Hi: When I was in school, we built an autonomous mobile robot based on a six wheeled, 'electric ride-on toy' from Toys-R-Us. It had a sturdy metal frame, two nicely geared motors, a decent battery. It worked fairly well and could carry a large (...) (28 years ago, 19-Oct-98, to lugnet.robotics.handyboard)
 
  (canceled)
 
 
  Re: Charging batteries
 
(...) There are also Renewal rechargeable Alkaline batteries from Rayovac. They have a special charger that shuts off so they aren't over charged. Cindy Salwen (28 years ago, 19-Oct-98, to lugnet.robotics)
 
  Re: waterproof seals (a bit OT)
 
(...) A little off the wall, but would it simplify the sealing if you could pressurize the inside to something close to the pressure outside (equalize pressures). A miniature CO2 cartridge with a release valve may help. Mike (28 years ago, 19-Oct-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR