 | | Re: Reading Datalog
|
|
The only VI I was able to find is at: (URL) is the purpose of the "UploadDatalog(nStart,nEnd)" function? Is there a way for Robolab to passively receive datalogs? The example I found seems to use the RCX in direct mode, but I am not sure as I do not (...) (17 years ago, 3-Jun-07, to lugnet.robotics)
|
| |
| | RE: Reading Datalog
|
|
RobotC RCX firmware is compatible with Robolab and the vast majority of the Ghost API messages. You can get this firmware by installing an evaluation copy of RobotC. If you are using Robolab, then there are a large variety of VIs available for (...) (17 years ago, 2-Jun-07, to lugnet.robotics)
|
| |
| | Reading Datalog
|
|
I am trying to get the Datalog from my RCX to be displayed on my computer. I am using RobotC to upload the datalog using the "UploadDatalog(nStart,nEnd)" function. It is sending the Datalog because I can see the green LED on the IR tower light up. I (...) (17 years ago, 2-Jun-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
(...) If you do support PIC18F8520, then with some changes to the loader one may be able to program VEX controller with Ultimate_PICLAB.which would be great! Guy Ziv (18 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
(...) ...snip (...) Perhaps I'll answer with a short list of projects that we have realized so far: 1.The most complicated thing I've done with Ultimate_PIC -I have to familiarize with that name now- using the 16F628A is a bi-directional half-duplex (...) (18 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | Re: events /nxt vs. events/rcx
|
|
(...) Sigh... "good luck"? I don't mean to sound too negative, but this is a hard nut to crack under the standard FW I think... at least I've yet to figure out a way to do it to my satisfaction. In fact, more than almost any other single point, this (...) (18 years ago, 31-May-07, to lugnet.robotics.nxt)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
(...) I'll forward this to Laurent. (18 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
"Claude Baumann" <cbaumann@ci.educ.lu> wrote in message news:JIvFwD.5C3@lugnet.com... (...) Exciting stuff! A friend and I have been using the PICKit2 recently for a range of chips including 12f's and 16f's. So far my personal favorite has been the (...) (18 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | Re: Ultimate ROBOLAB for PICs
|
|
(...) Any chance you'll add PIC18F8520 to the supported list of PICs? Guy Ziv (18 years ago, 31-May-07, to lugnet.robotics)
|
| |
| | events /nxt vs. events/rcx
|
|
Hi, I tried to write some code to simulate the events like in RCX. It starts to look cluttered. I understand that NXT VM does not support events like you find in the RCX. Any suggestion will be greatly appreciated! Elizabeth (18 years ago, 31-May-07, to lugnet.robotics.nxt)
|
