To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *43084 (-10)
  Re: error in using brickOS under Bricx Command Center
 
Thank you very much for your enduring kindness. (...) The content of helloWorld.mak is the same as that you wrote before. When I run make -f helloWorld.mak, I get nothing. When I run make -f helloWorld.mak after deleting helloworld.lx, I get make: (...) (21 years ago, 18-Oct-05, to lugnet.robotics.rcx.legos)
 
  Re: Spybot studies: seek a world object
 
(...) I can't find it right now, but I thought I read somewhere that if the direction is "anywhere", it will not have a direction. I believe that's consistant with what you're seeing. Steve (21 years ago, 18-Oct-05, to lugnet.robotics.spybotics)
 
  Re: NQC/BricxCC test
 
(...) This seems to have fixed all the problems that I was having with the serial tower and Bricx. [It also downloaded new (Swan)firmware OK] The template right-click is great too :-) I wasn't able test out the new (Vers.10) graphing part as I dont (...) (21 years ago, 18-Oct-05, to lugnet.robotics.rcx.nqc)
 
  Re: Spybot studies: seek a world object
 
Sorry, I forgot to mention I am using nqc 3.1r4 Allen (...) (21 years ago, 18-Oct-05, to lugnet.robotics.spybotics)
 
  Re: Spybot studies: seek a world object
 
John, perhaps you can help me with the directional capabilities. I have attached a copy of my code below. I am reading the direction to another spybot/beacon and putting it through a simple least squares adjustment. I find over short distance (HERE (...) (21 years ago, 18-Oct-05, to lugnet.robotics.spybotics)
 
  Re: Pictures of New technique: Cascaded Trinary Pneumatics (aka mid-stop)
 
(...) I'll start a schematic next week as this week is an unusual week at work. That should cover the pneumatic circuit. Basically, each stage gets a feed from the compressor, which goes to the middles of the two switches that drive the next stage (...) (21 years ago, 17-Oct-05, to lugnet.technic, lugnet.robotics)
 
  Re: error in using brickOS under Bricx Command Center
 
(...) Given that your OS Root setting was wrong before and now it is right then modifying that setting did help. It just didn't completely fix your problem. The OS Root setting in BricxCC needs to be set to the Cygwin path to the root of the brickOS (...) (21 years ago, 17-Oct-05, to lugnet.robotics.rcx.legos)
 
  Re: High Failure Rate of New Type 9V Geared Motor
 
(...) I had the same problem with one of mine. Using them in a fast RC car might do this if it gets slammed into something. I will inform Nathanael Kuipers of the problem since he works at TLC and can tell the proper person. (21 years ago, 17-Oct-05, to lugnet.robotics, lugnet.technic)
 
  High Failure Rate of New Type 9V Geared Motor
 
Bad tidings! I'm experiencing a rather high failure rate with the new type 9V geared motor (#43362). This motor has been discussed before ((URL) motor can be easily recognised: when you twirl the shaft it turns very little and quickly comes to a (...) (21 years ago, 17-Oct-05, to lugnet.robotics, lugnet.technic)
 
  Re: $60 for RCX 1.0 and Serial Tower
 
(...) But it's ok in the hands of AFOLs :-) C S Soh (21 years ago, 17-Oct-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR