To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *43079 (-10)
  Re: Pictures of New technique: Cascaded Trinary Pneumatics (aka mid-stop)
 
(...) I'll start a schematic next week as this week is an unusual week at work. That should cover the pneumatic circuit. Basically, each stage gets a feed from the compressor, which goes to the middles of the two switches that drive the next stage (...) (21 years ago, 17-Oct-05, to lugnet.technic, lugnet.robotics)
 
  Re: error in using brickOS under Bricx Command Center
 
(...) Given that your OS Root setting was wrong before and now it is right then modifying that setting did help. It just didn't completely fix your problem. The OS Root setting in BricxCC needs to be set to the Cygwin path to the root of the brickOS (...) (21 years ago, 17-Oct-05, to lugnet.robotics.rcx.legos)
 
  Re: High Failure Rate of New Type 9V Geared Motor
 
(...) I had the same problem with one of mine. Using them in a fast RC car might do this if it gets slammed into something. I will inform Nathanael Kuipers of the problem since he works at TLC and can tell the proper person. (21 years ago, 17-Oct-05, to lugnet.robotics, lugnet.technic)
 
  High Failure Rate of New Type 9V Geared Motor
 
Bad tidings! I'm experiencing a rather high failure rate with the new type 9V geared motor (#43362). This motor has been discussed before ((URL) motor can be easily recognised: when you twirl the shaft it turns very little and quickly comes to a (...) (21 years ago, 17-Oct-05, to lugnet.robotics, lugnet.technic)
 
  Re: $60 for RCX 1.0 and Serial Tower
 
(...) But it's ok in the hands of AFOLs :-) C S Soh (21 years ago, 17-Oct-05, to lugnet.robotics)
 
  Re: Pictures of New technique: Cascaded Trinary Pneumatics (aka mid-stop)
 
In lugnet.technic, Mark Bellis wrote: <snip> (...) Mark, I've tried to study the pictures, but I cannot resolve the mechanical linkages, and/or the pneumatic hookups. I was going to try to draw up a schematic, but I just can't resolve the images. (...) (21 years ago, 16-Oct-05, to lugnet.technic, lugnet.robotics)
 
  Re: MindStorm misc. willing to swap.
 
(...) Western Chicago suburbs......Naperville area. The "Scout" thing is pretty neat and appears to work. Makes lots of noises, lights turn on & off..... (URL) to swap it all in one lot if possible. (21 years ago, 15-Oct-05, to lugnet.robotics)
 
  Re: $60 for RCX 1.0 and Serial Tower
 
Hi CSSoh, (...) yes, I cut out the wrong lines, I meant the one with AC adapter. (...) Maybe it is also too easy to fry the RCX that way, e.g. by using a transformer with a wrong voltage, and the customer service costs got out of hand. Cheers (...) (21 years ago, 16-Oct-05, to lugnet.robotics)
 
  Re: error in using brickOS under Bricx Command Center
 
I am able to use (compile and download) brickOS under cygwin but not under BricxCC. (...) I am sorry to say that the modification in the "OS root" setting didn't help. In fact I installed BricxCC in 2 of my computers. Both show the same error (...) (21 years ago, 16-Oct-05, to lugnet.robotics.rcx.legos)
 
  Re: Pictures of New technique: Cascaded Trinary Pneumatics (aka mid-stop)
 
(...) Hi Kevin, Yes, the bottom right stage is the control stage, with 2 active switches. I left the third one in to keep the stability with the cams and 2L liftarms so that the 1x4 brick with holes moves as a parallelogram. I got into the habit of (...) (21 years ago, 15-Oct-05, to lugnet.technic, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR