 | | Re: data recording in BrickOS ?
|
|
Am Mon, 26 Sep 2005 12:35:05 GMT "Francois Bardet" <f.bardet@voila.fr> tippte: (...) this is not the default i programmed this functions, but the docu is in only in german avialible if you can read german, have a look at (URL) there was an other (...) (21 years ago, 26-Sep-05, to lugnet.robotics.rcx)
|
| |
 | | Re: Can't upload new program after I have used LNP under brickos
|
|
(...) You had to turn on the lnp, with something like this: (I forget the exact commands) lr_startup(); lr_init(); lnp_init(); Make sure you turn it off: lr_shutdown(); Steve (21 years ago, 26-Sep-05, to lugnet.robotics.rcx.legos)
|
| |
 | | data recording in BrickOS ?
|
|
Hi Mindstormers, 1) Does BrickOS allow to write/read measured data into the RCX memory, in order to plot or process it later on the computer ? If yes, what are the command lines to : - allocate the memory space ? - to write and read ? - free this (...) (21 years ago, 26-Sep-05, to lugnet.robotics.rcx)
|
| |
 | | Re: New technique: three position piston control
|
|
In lugnet.technic, Mark Bellis wrote: <snip> (...) Was this single or dual piston? (...) Kevin (21 years ago, 26-Sep-05, to lugnet.technic, lugnet.robotics)
|
| |
 | | Can't upload new program after I have used LNP under brickos
|
|
Hello, |I have the following problem: |when I use lnp under brickos, the rcx does no longer respond to the legotower. |This means that I can't delete the program nor overwrite it. | |Pershaps somebody can help. | |Thanks, | |Andy (21 years ago, 26-Sep-05, to lugnet.robotics.rcx.legos)
|
| |
 | | Unable to delete programm after having used lnp under brickos
|
|
Hello, I have the following problem: when I use lnp under brickos, the rcx does no longer respond to the legotower. This means that I can't delete the program nor overwrite it. Pershaps somebody can help. Thanky, Andy (21 years ago, 26-Sep-05, to lugnet.robotics.rcx)
|
| |
 | | Re: Some beginner questions on serial communication
|
|
Hi, (...) Sorry, I don't have an RCX so can't really help you there. The NQC Guide is pretty good. The best way to find out is to try lots of combinations. (...) Here are a couple of programs where two Spybots send messages to each other. Another (...) (21 years ago, 26-Sep-05, to lugnet.robotics.spybotics)
|
| |
 | | Re: New technique: three position piston control
|
|
(...) <snip> (...) The center stop is not the same spot when expanding vs. contracting. I did not try it at different pressures. I just pumped a hand pump as fast as I could to make the sequencer go. I've not seen it overshoot the mid point. (...) (...) (21 years ago, 25-Sep-05, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: New technique: three position piston control
|
|
In lugnet.technic, Kevin L. Clague wrote: (SNIP) (...) Interesting stuff! Should make walkers move more smoothly, with the possibility of more groups of legs. The trick will then be reversing all the groups, since it was easier with just two, using (...) (21 years ago, 25-Sep-05, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: Spybot studies: seek a world object
|
|
(...) Well We are trying to get Spybotics following an IR emitting Ball.. This ball will be emitting the same data as the Controller does on blinking mode.. But somehow the program above (as said before) Will not work propperly and send the spybot (...) (21 years ago, 25-Sep-05, to lugnet.robotics.spybotics)
|