 | | Re: mmu
|
|
It's not impossible. The easiest way is to use the same technique as Java (or IC) and write an embedded interpreter that executes code for a "psuedo" machine. The resulting machine can have arbitrarily strict access restrictions between tasks. You (...) (28 years ago, 11-Aug-98, to lugnet.robotics.handyboard)
|
| |
 | | PCB
|
|
fthompson wrote: "Some time ago Karl Lundt included in his Amateur Robotics column a short description of a new Printed Circuit Fabrication material where you ran the copper clad through a laser printer (to print directly onto the copper rather than (...) (28 years ago, 11-Aug-98, to lugnet.robotics.handyboard)
|
| |
 | | intel hex file
|
|
Hello all, Does anybody has information of the intel hex file. I do understand the intel hex file (xxx.hex) that is generated by the asm programs, but i use a new assembler, (with the gcc compiler) and it generates different intel hex file (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
 | | PID implementation
|
|
Problem: I have built a small robot with differential drive using 3+ACI- diam whee ls turning at 66 RPM +AEA- full power PWM no load. Each wheel has a 16 pulses per rev. reflective type shaft encoder. the robot is controlled by the Handy Board (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
 | | serial library for C++
|
|
Hello, I have a handy board with poloroid transducers and I am trying use the results of my distance measurments in a C++ program on the computer. I have found programs on the handyboard web page that should alow the handyboard to transmit (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: serial library for C++
|
|
Check out this site. It works well. The only problem I had was timing issues when trying to read and write to the port too quickly. (URL) Message----- From: Mark Wallace <mawalla3@vt.edu> To: Handyboard@media.mit.edu <Handyboard@media.mit.edu> (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Some robot pictures
|
|
Cool robots, Chuck! I was wondering it when they were created. It looks like the top one was created first and the last is the bottom one. Is that so? ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
 | | Stepper motors
|
|
Hello, Does anyone have information on how to run a stepper motor using the Handy Board? Any information you can provide would be appreciated. Mario Garcia (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Some robot pictures
|
|
Thanks for the Kudos, Actually the timeline is more like "Clyde" (not pictured), "Robotank" (Sherman chassis with a miniboard), "RobotTankII" (Sherman Chassis with 6.270 board), "Comet" (not pictured, R/C conversion w/Miniboard), "Ghost" (not (...) (28 years ago, 12-Aug-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Stepper motors
|
|
Hello mario, Its actually very simple, use an uln2803, connect it to an not used port (i.e. porta in my case), connect the coil wires to the appropriate pins, and the supply lines to the stepper vcc. now you can write values to the port. you should (...) (28 years ago, 13-Aug-98, to lugnet.robotics.handyboard)
|