 | | Re: 5-DOF arm
|
|
(...) I would like to see some pictures. Thanks, Kev (21 years ago, 17-Sep-05, to lugnet.robotics)
|
| |
 | | RE: time sampling under the rcx standard OS
|
|
Here are some comments on how to improve your code for real-time performance. 1. Move the "SetUserDisplay" out of the loop and put it just before the loop. 2. I think the "OnFwd" macro is actually two instructions: "Fwd" and then "On". Replace this (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: time sampling under the rcx standard OS
|
|
(...) From what I've seen, the standard firmware takes about 3ms per command, and the same program will run on BrickOS about 100 times faster. I usually set up my BrickOS programs so they use the internal timer, and only update the motor setting (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: time sampling under the rcx standard OS
|
|
(...) Francois, I think you should be able to get much faster sampling. I can easily get 10-20 Hz, and others have claimed to get down to 3 ms. Whether it can be done at a constant rate, I'm not sure, and think it probably depends on what else is in (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | time sampling under the rcx standard OS
|
|
Hi list, I'm trying to implement a position regulation (using a motor and a rotation sensor), using for instance a PID (Proportional-Integr...erivative) regulation. I tried to code it in NQC, using the standard OS, but it seems that the RCX loops at (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | time control : BrickOS versus the RCX standard OS ?
|
|
Hi list, I'm trying to implement a position regulation (using a motor and a rotation sensor), using for instance a PID (Proportional-Integr...erivative) regulation. I tried to code it in NQC, using the standard OS, but it seems that the RCX standard (...) (21 years ago, 17-Sep-05, to lugnet.robotics.rcx.legos)
|
| |
 | | 5-DOF arm
|
|
Hi everyone -- I have recently completed my Nth version of a 5-DOF arm plus claw. Finally, I am guardedly happy with the result. I think it's about as minimalist as such a thing can be; it's much smaller than models with similar capability I've seen (...) (21 years ago, 17-Sep-05, to lugnet.robotics)
|
| |
 | | IR-based proximity measurement
|
|
I'm changing the subject line in the middle of the thread. Wonder what the server will do with that... I tried out Brian's "Max-picking" ping method, as well as a few other things. Here's a summary of what I found: 1) If the active sensor readings (...) (21 years ago, 16-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: direct manipulation of bits in RCX registers using NQC
|
|
(...) Correct. A NQC command (say, "Wait(10);") is converted to one or more "bytecodes" (in this case, one bytecode, namely a string of 4 bytes (0x43 0x02 0x0a 0x00), the first of which is a command (0x43) while the following three are information (...) (21 years ago, 16-Sep-05, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: direct manipulation of bits in RCX registers using NQC
|
|
Hey, Thanks for all the helpful responses, everyone. Brian: (...) I guess that "firmware" must be the code that tells RCX how to interpret user instructions (NQC, C, IC, opcodes, or whatever), and convert them to binary machine-specific code. Right? (...) (21 years ago, 16-Sep-05, to lugnet.robotics.rcx.nqc)
|