 | | Re: Barcodes & error detection
|
|
(...) I actually started out this way, before getting lost in the number of combinations. After you suggested it, I may actually reconsider, because: (...) Perhaps less; right now the reflective strips don't really encode information, they just (...) (21 years ago, 8-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Barcodes & error detection
|
|
(...) Agreed, and, for this application, the bit overhead to allow on-board correction is probably just not worth it. After all, if an error is detected, the forklift can always back up and try to read the barcode again. (...) Almost exclusively (...) (21 years ago, 8-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Barcodes & error detection
|
|
Thanks, you actually made me pull out one of my old comp sci texts :-) I remembered studying this stuff many moons ago .... Error detecting requires a "distance" between codes of at least TWO ... what this means is to detect a single bit error each (...) (21 years ago, 8-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Barcodes & error detection
|
|
(...) Well, there is a sharp distinction between error DETECTION and error CORRECTION. It's also important to characterize the errors you are getting. Are you getting single bit errors or multi-bit errors? You will certainly need to use more bits in (...) (21 years ago, 8-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Barcodes & error detection
|
|
(...) Right off hand I don't know any checking mechanism that works best with false readings of one polarity. Do you know anything about Error Correction Codes? ECC is used to detect and correct single bit errors, it can also detect double bit (...) (21 years ago, 7-Sep-05, to lugnet.robotics)
|
| |
 | | Re: New Diagrams of Basic Pneumatics Parts and Circuits
|
|
(...) James, What all have you tried. One of the best compressors using a Mindstorms mini-motor is the Ralph Hempel design, as shown by Dr. C. S. Soh's page: (URL) If you want to go all out, a very simple, and powerful compressor is: (URL) The issue (...) (21 years ago, 7-Sep-05, to lugnet.robotics)
|
| |
 | | Re: Barcodes & error detection
|
|
(...) One suggestion that may improve your reliability is to use colour transitions rather than just colours. This would mean, however, that you would need more strips. For example, if you currently represent B=0 and W=1 your barcode for 0110 would (...) (21 years ago, 7-Sep-05, to lugnet.robotics)
|
| |
 | | RE: New Diagrams of Basic Pneumatics Parts and Circuits
|
|
The drawings are FABULOUS! Great work. I have a question: I am looking to build a lego compressor that would be strong enough to move a quad or sextuple bot with the RCX. We have tried a few with no luck - never produces sufficient air or pressure. (...) (21 years ago, 7-Sep-05, to lugnet.robotics)
|
| |
 | | Barcodes & error detection
|
|
Some of you at BrickFest may have seen Gus, a small robotic forklift that was one of my GBC modules. Gus had two problems at BrickFest. First, while the codereading task was 98% accurate, that still means on average once every 16 circuits of the (...) (21 years ago, 7-Sep-05, to lugnet.robotics)
|
| |
 | | New Diagrams of Basic Pneumatics Parts and Circuits
|
|
I've just uploaded some new pneumatics diagrams, the sort that could guide people towards the complex systems we've been discussing in .technic: All were originally drawn in Visio. The circuits themselves are all ones used in official sets, the last (...) (21 years ago, 7-Sep-05, to lugnet.technic, lugnet.robotics, lugnet.loc.uk, lugnet.cad)
|