To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4236 (+10)
  Re: Polaroid trouble again
 
I had this same problem when I got mine a few weeks ago. I ended up putting a capacitor from pin 1 to pin 3 on U2 of the sonar driver board. I also had to take out the 1k resistor from the BINH. It kept BINH at 1 V instead of Zero and that seamed (...) (28 years ago, 3-Aug-98, to lugnet.robotics.handyboard)
 
  Re: Polaroid trouble again
 
You may be trying to draw more current that your external battery can handle. The HB Nicd battery can supply alot of current, both surge abd continuous. This may be why it works in this case. If your external battery is not NiCd, it might cause a (...) (28 years ago, 3-Aug-98, to lugnet.robotics.handyboard)
 
  speed of the board
 
Hi guys, I am worried about the 2MHz clock speed of the HB. The robot that I am building has a mouse in the bottom of it and I am writing the program to read the number of digital pulses and calculate the position relative to the starting point. (...) (28 years ago, 3-Aug-98, to lugnet.robotics.handyboard)
 
  Re: Polaroid trouble again
 
(...) I haven't used the Polaroid module with my HB, but I have used them a lot with 68332 micro-processors. I does sound like you may have an electrical noise problem (not EMI, but noise conducted through the power bus). The only way I've got the (...) (28 years ago, 3-Aug-98, to lugnet.robotics.handyboard)
 
  RE: speed of the board
 
You shouldn't lose place if the mouse is serviced by input counters and interrupt routines, so whether 2 MHz is fast enough depends on how often you need the positions calculated from the mouse counters. You won't be able to get that as fast as the (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
 
  Re: speed of the board
 
the other issue that should be mentioned re: changing clock speed is that it messes up the baud rate of the serial communications. if you plan to use interactive C, would have re-assemble the pcode program with a different baud rate constant, to (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
 
  Need Simple IC editor
 
Howdy. Thanks to everybody who gave me advice when I wrote about some basic issues. Your responses included links to a C- compiler, a C tutorial, an electronics tutorial, and more! I managed to get my HB up and running and have begun tinkering (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
 
  Re: speed of the board
 
anton, You might want to think about getting rid of all those square roots. Take a look at what you are really trying to do and decide if you need the square root. For example, if you are just compairing two distances to see which is greater, you (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
 
  Handy board Expansion
 
hi, I have gone thru the Handy board expansion schmetic circuit version 3.0 by Mr.Fred Martin whcih updated on the June 14,1998. I have some doubts : 1) What and where is the the Analog pass-through connector (J4) and Motor power pass-through (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)
 
  Where and when to buy a HandyBoard?
 
Hi all, I am considering purchasing a handyboard, but Definitly want to get the sensor expansion board when available. 1) Do I need to purchase a specific handyboard in order to get the I/O expansion board to work? 2) Is Gleason Research a good (...) (28 years ago, 4-Aug-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR