To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *41539 (-10)
  Re: MOC: Egglift, a Lego Appliance to cook soft-boiled eggs
 
(...) The range of the Lego temperature Sensor is -20o C to 70 o C. You can see one reading below. As you can see, I'm almost off limit. (URL) (...) From my test, definitely the sensor would go off range first. Probably that's the reason why TLC (...) (22 years ago, 15-Jan-05, to lugnet.robotics, FTX)
 
  Re: Technic plates
 
(...) The shank with the dimension is galled up but it fits the 3/16" hole in the bit racks - I've got more than a few sets of drill bits and loose ones hanging around. I simply looked for the bit that provided a good fit (no slop) in a stack of 8 (...) (22 years ago, 15-Jan-05, to lugnet.technic, lugnet.robotics)
 
  Re: MOC: Egglift, a Lego Appliance to cook soft-boiled eggs
 
(...) Phew, I can feel the heat! What was the reading recorded by the temperature sensor? As I recall the LEGO Temperature sensor range is from -20 degrees Celsius to +50 degrees Celsius. Would the sensor go off range or would the ABS melt first? CS (22 years ago, 15-Jan-05, to lugnet.robotics, FTX)
 
  Re: MOC: Egglift, a Lego Appliance to cook soft-boiled eggs
 
(...) I think it was 'Ben' Beneke if thats any help, but his site has moved fairly recently. Tim (22 years ago, 15-Jan-05, to lugnet.robotics, FTX)
 
  Re: Technic plates
 
As I might have noticed, the Lego technic holes are exactly 4.8mm. This technique is also good to create "technic bricks" - very usable when you need a more stabilized axle-guide. Just drill a standar 2X* brick through the cilinders from the bottom, (...) (22 years ago, 14-Jan-05, to lugnet.robotics)
 
  Re: Technic plates
 
(...) This sounds like a good idea. What size drill bit did you end up using? (22 years ago, 14-Jan-05, to lugnet.technic, lugnet.robotics)
 
  Technic plates
 
I was just putting together the classroom packs I use for teaching robotics. Each two student team is given a tray of "standard" parts to work with. To make life easier I have tried to "color-coded" these sets with all components (as much as (...) (22 years ago, 14-Jan-05, to lugnet.technic, lugnet.robotics) ! 
 
  Re: combining LDCC and NQC style automation?
 
(...) If you'd rather do a little hardware work, than learn pbForth, I have a couple suggestions. 1) You could use LEDs instead of regular lights. An LED will only light, when the power is going the correct direction. So you could connect 1 LED to (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: combining LDCC and NQC style automation?
 
[big snip] (...) I do have DCC in the latest pbForth, but I've sort of dropped official support for older versions of MacOS. That being said, I think the instructions are still up on the site for getting it to work. :-) Please post here if you;re (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx, lugnet.trains)
 
  Re: combining LDCC and NQC style automation?
 
Christopher Masi wrote: [snip] (...) [snip] (...) I know, replying to myself, bad form. I have also discovered that pbForth has DCC worked into it. The good new here (although I have only looked at the introduction on the home page) is that Raplph (...) (22 years ago, 14-Jan-05, to lugnet.robotics.rcx, lugnet.trains)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR