To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *41414 (-10)
  Re: Robolab Documentation
 
The replacement firmware has several modes for displaying the clock. HH.MM, MM.SS and M.SS.S. The first format is the Lego standard whcih I find failry uninformative. The clock is reset to zero whenever RCX is powered up although many IDE's reset it (...) (22 years ago, 7-Jan-05, to lugnet.robotics.rcx.robolab)
 
  Re: NQC 1.0 compatibility mode
 
(...) I know I got stung with it when I first installed the IDE, not having it woulda saved me a couple of posts to Lugnet :) ROSCO (22 years ago, 7-Jan-05, to lugnet.robotics.rcx.nqc)
 
  Re: NQC 1.0 compatibility mode
 
(...) I think if they need NQC V1, they won't have this new IDE. If they have the new IDE, they won't have NQC V1.x (22 years ago, 7-Jan-05, to lugnet.robotics.rcx.nqc)
 
  Re: Robolab Documentation
 
(...) based on a question that I asked back on Dec 11: "I followed instructions replacing firmware.txt with the replacement file as instructed. The download went smoothly,immediately upon finishing (two beeps) the LCD screen started counting in (...) (22 years ago, 7-Jan-05, to lugnet.robotics.rcx.robolab)
 
  RCX Sensor Port
 
I've been looking into the interface of the RCX sensor port, as well as studying available information. This page from Stef Mientki suggests that the port uses a current source: (URL) believe this to be correct. According to the circuit topology and (...) (22 years ago, 7-Jan-05, to lugnet.robotics)
 
  LNPd keeps sending TX_FAILURE
 
I'm running LNPd on Gentoo Linux 2.6.7. Everything seems to work fine except transmitting messages to the RCX. The lnptest application that comes with LNPd keeps reporting a Collision every time it tries to transmit something. It does however (...) (22 years ago, 7-Jan-05, to lugnet.robotics.rcx.legos, FTX)
 
  NQC 1.0 compatibility mode
 
Would anyone miss terribly the NQC 1.x compatibility mode if I were to remove it? At this point it seems like it is a very useless feature, but maybe someone out there is still using the 1.x API. What do you think? John Hansen (22 years ago, 6-Jan-05, to lugnet.robotics.rcx.nqc)
 
  Re: Uses for tacho wheel?
 
(...) Whilst white tacho wheels were used by the barcode truck for speed sensing (on the truck for variable engine rev sounds), the Star Wars UCS X-Wing used grey ones on the cannons(?) on the wings. Tacho wheels have 8 slots that will hold flex (...) (22 years ago, 6-Jan-05, to lugnet.robotics)
 
  Re: Uses for tacho wheel?
 
(...) They were used to interupt the light beam/sensor on the Code Pilot allowing the Code Pilot to sense shaft rotation. -Rob. (22 years ago, 5-Jan-05, to lugnet.robotics)
 
  RE: Uses for tacho wheel?
 
If you point a light sensor at them, you can use them as a rotation sensor. They are also available in one of the NBA basketball sets. If memory serves, they used it as a gear that was part of a ratchet mechanism to keep the wind-up motor from (...) (22 years ago, 5-Jan-05, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR