To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *41374 (-20)
  questions on events
 
Are events stackable? Or it works more like "signal()", e.g. in C? e.g. I have 2 different light sensor events set to watch for value higher than 42, yellow & blue. Let say both sensors read 45 at the same time, RCX returns only one event being (...) (22 years ago, 2-Jan-05, to lugnet.robotics.rcx.robolab, lugnet.robotics.rcx.nqc)
 
  Re: 2-wheelers
 
I've been looking at that little piece of code, and trying to duplicate its effect in my YAL-based program, without much luck. When I had Steve's code running, it did tend to stay in one spot, but it eventually became unstable. At this point I plan (...) (22 years ago, 2-Jan-05, to lugnet.robotics)
 
  Re: RCX IR Transceiver and Sensor Port Circuits
 
hi Mark, i have learned a lot from your RCX IR Transceiver Circuit. Things i did not know before. But please dont forget to show us that Sensor Board Circuit. As far as i know, a real introduction into designing RCX selfmade Sensors is not available (...) (22 years ago, 1-Jan-05, to lugnet.robotics)
 
  New invention instructions
 
Where can I get new inventions and their building instructions besides those given in Lego Mindstorms Robotics Invention System 2.0? (22 years ago, 1-Jan-05, to lugnet.robotics)
 
  Re: 2-wheelers
 
(...) I think another huge difference (for me at least) is that Steve's code learns where the upright position is, while most of the others need to be put down in the correct position. (That is what the piece of code does in the 50ms if()). John (22 years ago, 1-Jan-05, to lugnet.robotics)
 
  2-wheelers
 
I don't know if anyone cares about this, but -- I think I figured out something about Legway-type bots and the software that drives them. The puzzle is: why do some versions need a full PID controller (Proportional-Derivative Integral feedback), (...) (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Transistors used in Lego Electronic products
 
Can anyone tell me what type of transistor is in a surface mount package marked "E16"? They're used in the Cybermaster radio tower. Are the transistors NPN or PNP? Do they have the usual pin-out (collector on its own, base and emitter on the other (...) (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Re: controlling RC-servos
 
(...) Again, I forgot the link : (URL) (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  controlling RC-servos
 
Ultimate ROBOLAB v. 1.4.5.7 now has the feature to control 1 to 3 RC-servo motors with full access to the normal Ultimate RCX-functionality. This version will be available soon for beta-testing. Cheers, Claude (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Re: RCX IR Transceiver and Sensor Port Circuits
 
(...) Thanks Mark, it's on my page, but as I said it's mess, so it's on a slightly different page: (URL) hope to rearrange my Lego Website in one of the next months, but first I've to write a decent html editor ;-) cheers, Stef (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Re: balancing bot
 
I recently implemented a new motor control "source" specifically targeted at PID algorithms in the new firmware. It takes a signed number in the range -128 to +128 and converts it into a motor control command. -128 to -1 is reverse direction and (...) (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Re: balancing bot
 
(...) that would be interesting, but I meant the wheels. (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  Re: balancing bot
 
this looks similar to the logic I got working. I tweaked the parameters (equiv. to a,b,c in your code) and it's much more stable now. Interestingly, I have to set 'b' very high, about 2X of what 'a' is set to -- most code I've seen is just the (...) (22 years ago, 31-Dec-04, to lugnet.robotics)
 
  crosscompiler does not compile arrays of objects
 
Hello! I made a cross-compiler with the sources of gcc-3.4.2 and tried to compile this: Behavior a(); Behavior b() Behavior behaviors[] = {a,b}; ... Make fails with the error message: conversion from Behavior()() to non-scalar type Behavior (...) (22 years ago, 30-Dec-04, to lugnet.robotics.rcx.legos)
 
  Re: balancing bot
 
thanks much for the links! Using a mod of Frederic Siva's code, I've managed to get my bot somewhat stable. It wobbles around like a drunken sailor but basically stays up. I've got a movie file of it careening around the floor for about a minute (...) (22 years ago, 30-Dec-04, to lugnet.robotics)
 
  Re: balancing bot
 
(...) ...and here is a NQC sample code that works on YAL, using Dick Swan's fast firmware. Try it on a clear color surface (not necessarily even, some patterns help stabilize position) with overhead diffuse lighting. YAL must be started balanced (...) (22 years ago, 30-Dec-04, to lugnet.robotics)
 
  Re: balancing bot
 
(...) There was one design out there that works with standard Lego - but it has (IIRC) two light sensors out on long booms in front and behind the robot. At those distances from the pivot point, they move a much larger distance than if they are (...) (22 years ago, 30-Dec-04, to lugnet.robotics)
 
  Re: balancing bot
 
(...) You may have a look to YAL: (URL) (22 years ago, 30-Dec-04, to lugnet.robotics)
 
  Re: balancing bot
 
Hi Dan, (...) I have also been playing with it the last week or so and got it to work. At the end I used Steve's legway.c program with everything except the balancing removed and used the raw sensor values, tweaked a bit. That together with two (...) (22 years ago, 30-Dec-04, to lugnet.robotics)
 
  balancing bot
 
hi all-- lately I've been playing with legway-inspired ideas. After much frustration, I'm finally getting some results using a standard lego light sensor with some custom enhancements (not taking it apart, just adding a lens and a light source). At (...) (22 years ago, 30-Dec-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR