 | | Re: Using Code Pilot to control motorized cows
|
|
(...) Note that Jason Allemann created a smaller version, more akin to minifig scale: (URL) motor has to be in the base, but other than that it works exactly the same. ROSCO (22 years ago, 3-Dec-04, to lugnet.robotics.codepilot)
|
| |
 | | Re: Light seeker
|
|
(...) Why do you use two light sensors? I have made experience with one light sensor mounted on top of a motor driven and rotation sensored turret. The mechanics has two drawbacks. First, the geartrain between motor and light sensor is somewhat (...) (22 years ago, 2-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Errors while installing brickOS 0.2.6.10
|
|
(...) I highly recommend that you use my cygwin and brickOS installers. If you use them you will more than likely be up and running with brickOS in a matter of minutes. See my BricxCC page at (URL) are links to the two installers: (URL) Hansen (22 years ago, 2-Dec-04, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
 | | Using Code Pilot to control motorized cows
|
|
Purists please skip this post as it involves non-LEGO sensors. Lacking an RCX, but loving the motorized cows ( (URL) ), I needed to find a way to control them with the code pilot (from set 8479 Barcode Multi-Set) I have. The only LEGO sensor that (...) (22 years ago, 2-Dec-04, to lugnet.robotics.codepilot, lugnet.trains)
|
| |
 | | Errors while installing brickOS 0.2.6.10
|
|
Hi, I am a newbie. I have encountered some errors while installing brickOS 0.2.6.10. (URL) anyone encounter the same problems before? 1. When I just start cygwin, it gives me an error message like this: This application program can not be executed (...) (22 years ago, 2-Dec-04, to lugnet.robotics, lugnet.robotics.cybermaster, lugnet.robotics.edu, lugnet.robotics.rcx, lugnet.robotics.rcx.legos, lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Motor Speed Control
|
|
(...) That's the case too for Swan firmware with standard parameters. (...) And yes, power consumption is much higher using on break. I measured variation of RCX current with one motor, power level 3 (50% duty cycle). Idle RCX current (35mA) is (...) (22 years ago, 1-Dec-04, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: That doesn't totally seem right.
|
|
(...) The datalog was 27 but is now 100 (I was pushed for time earlier). (...) That's exactly what happens now. (...) I can now see that the zero's fade over time. Here's the latest results. Variable 4: 1 Variable 4: 5 Variable 4: 0 Variable 4: 4 (...) (22 years ago, 1-Dec-04, to lugnet.robotics)
|
| |
 | | Re: That doesn't totally seem right.
|
|
(...) If you're storing this all in the datalog, you should be able to go much farther than 27 times through the loop. Try storing a couple hundred values (how big is the datalog?) Then, you should see the time-between-changes get bigger. Also, it (...) (22 years ago, 1-Dec-04, to lugnet.robotics)
|
| |
 | | That doesn't totally seem right.
|
|
(...) That occured to me after my last posting, but I can't think why it wouldn't slow. (...) Yes, your right. I've switched to the 10x Swan firmware, and stored the results in the datalog. Here they are Variable 4: 4 Variable 4: 0 Variable 4: 3 (...) (22 years ago, 1-Dec-04, to lugnet.robotics)
|
| |
 | | Re: RCX and the 9v system - help needed!
|
|
(...) Ah, yes, the cows! I remember them. Brilliant idea and within my realm of expertise! Thanks. Chris (22 years ago, 1-Dec-04, to lugnet.robotics, FTX)
|