To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *40989 (-10)
  Re: BricxCC 'Float' Command not working on Scout
 
(...) Try adding a Wait(500) after the Float command. It'll float for 5 seconds then brake. Apparently, the default state is brake when no program is running. Mark (22 years ago, 28-Oct-04, to lugnet.robotics)
 
  Crazy idea - analog computer
 
Hello, 1st I don't want to put this as an alternative to mindstorns but since I don't have mindstorms and the money for the starter kit I was thinking after seeing a web of old analog computers, Is it possible to do a programble analog computer with (...) (22 years ago, 28-Oct-04, to lugnet.robotics)
 
  Re: bad motor output because of lego firmware?!
 
(...) I suspect part of this delay is inherant to the firmware, and won't be "patchable" In any case, if you want your extender to be something you can market to most users, it should work with the standard firmware, without modification. Just my (...) (22 years ago, 28-Oct-04, to lugnet.robotics.rcx.nqc)
 
  Re: bad motor output because of bad lego firmware?!
 
(...) The firmware (at least version 0328) intentionally prevents you going directly from forward to reverse (or vice versa). I guess the designers felt this would be too rough on the motors. Try inserting a Wait(50) in your first loop. It'll work (...) (22 years ago, 28-Oct-04, to lugnet.robotics.rcx.nqc)
 
  bad motor output because of bad lego firmware?!
 
Hi there, I've spent the last two days trying to write a function in NQC that transfers data to the Lepomux I/O-extender. The data transfer is normally done by connecting the Lepomux to one of the motor ports. Each transition from one motor state to (...) (22 years ago, 28-Oct-04, to lugnet.robotics.rcx.nqc)
 
  Re: Help installing brickOS
 
(...) Sure. The configure script tries to find the gcc cross compiler toolchain for the brick's hitachi processor. This chain is needed to compile brickOS to a program that can be run by the RCX. But it seems that you did not install the tool chain. (...) (22 years ago, 28-Oct-04, to lugnet.robotics.rcx.legos)
 
  BricxCC 'Float' Command not working on Scout
 
While programming a Scout using BrickCC, no matter how many times I tried, I could not get the Scout to 'float' its motors. The program was as follows- task main() { OnFwd(OUT_A); Wait(50); Float(OUT_A); } After a half second the motor would brake, (...) (22 years ago, 28-Oct-04, to lugnet.robotics)
 
  Re: Help installing brickOS
 
(...) I believe that I had the exact same problem a few weeks ago, but I found that using a pre-built package takes a lot of the hassle out of installing BrickOS. The pre-built packages can be found at: (URL) hope this helps, Timothy (22 years ago, 27-Oct-04, to lugnet.robotics.rcx.legos)
 
  Help installing brickOS
 
I'm trying to install brickOS 0.2.6.10.6 on WIN NT. After unning "configure" it's busy for along time, and terminates with the message -"No Hitachi gcc compiler found. Please install compiler and try again." Any suggestions? Thanks, Jordon (22 years ago, 27-Oct-04, to lugnet.robotics.rcx.legos)
 
  GASTON
 
Hi all, 1. Finally most of the documents, building instructions, schematics and so on are available concerning our robot GASTON (URL) Ultimate Robolab is advancing well and will soon be available for beta-testing: (URL) (22 years ago, 27-Oct-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR