 | | Re: Add motor driver to RCX
|
|
(...) John Barnes (HiTechnic) has available a motor amplifier which draws it's power from an external source, and can control 4 motors from 1 RCX ouptut. I haven't tried one, but you might find it helpful: (URL) (22 years ago, 5-Aug-04, to lugnet.robotics.rcx)
|
| |
 | | Re: Add motor driver to RCX
|
|
(...) What does this mean in electrical novice terms? What is an auto-coupler? Is it possible to modify the reciever/power unit to interface with the RCX? ie maybe add an inferred recuever to interpret commands from the rcx to power the motors (...) (22 years ago, 5-Aug-04, to lugnet.robotics.rcx)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) Except that this is a problem pretty easily solved in code -- it's not necessary that the robot choose the same solution the original builder did; it's only necessary that it choose a solution that works. A robot that copies only continuous (...) (22 years ago, 5-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) Ah, hmm, I was expecting it to be a continuous fabric, not a holey one. That would make it harder, and in fact makes it even more important to not confuse neighboring pieces of the same color (otherwise you could lose structural integrity by (...) (22 years ago, 5-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) Yes, but not arbitrarily -- there would be some limit in width (Y) and height (Z), in order for the model to fit into the machine. (...) Yes, that's a much harder problem, which is why I was thinking to limit it to a thickness of one in X. (...) (22 years ago, 5-Aug-04, to lugnet.robotics)
|
| |
 | | Re: laser distance sensor
|
|
(...) Who said you had to actually use laser? :) Google for "electronic tape measure" to see what I'm talking about (they really use sonar, with a laser pointer to show where the device is reading from). Home Depot has one for $29. Now, the biggest (...) (22 years ago, 5-Aug-04, to lugnet.robotics.rcx)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) Okay... I think I understand... so you use some 1xN plates or bricks on the top and the bottom of the whole "picture" to hold it together, and the actual construct built can be any size of width N? Or am I still way out there? >> Mark (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) OK, just to clarify: assume an X-Y-Z space with studs sticking up in the Z direction. You mean a model that's only one stud thick in X, arbitrarily wide in Y, and arbitrarily high in Z? Yes, that would be a much simpler problem than what I was (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
(...) The closest I got to something like that was my half-built Duck Assembly Carousel - a dial automation with 4 positions, which would assemble the body (2x1 inverted slope), beak (2x1 plate), and head (1x1 brick with a hole in it). I didn't have (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|
| |
 | | Re: challenge: LEGO copier
|
|
Would the bricks be assembled as a wall one brick thick on its side? Like laying a cinderblock wall on its side then creating a copy? That might be done with an X-Y table arrangement with vice like sides at top and bottom of the bricks so that they (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
|