 | | Seattle Road Show (whoops- a week late...)
|
|
The Road Show came to Seattle on the last weekend of September, running from the 26th to the 28th. PNLTC, SeaLUG, and SMART all shared the small space with a 3-layer layout in 4 sections. You can check out a sampling of the pictures on the SeaLUG (...) (23 years ago, 6-Oct-03, to lugnet.events, lugnet.announce, lugnet.lego.direct, lugnet.space, lugnet.castle, lugnet.trains, lugnet.robotics, FTX)
|
| |
 | | Re: serial speed of RCX
|
|
(...) Hi Tom, The highest baud rate you can generate appears to be 500Kb given the 16MHz CPU clock. There's a formula for calulating baud rate after Table 11-3 (page 205) in my version of the hardware manual. HTH, Mark (23 years ago, 6-Oct-03, to lugnet.robotics)
|
| |
 | | serial speed of RCX
|
|
Hello everyone ! I'd like to ask you another question about my idea changing the communication interface of the RCX. Does anyone of you know, how fast the serial port of the H8 controller used in the RCX is able to work ? If you look up the (...) (23 years ago, 6-Oct-03, to lugnet.robotics)
|
| |
 | | serial speed of RCX
|
|
Hello everyone ! I'd like to ask you another question about my idea changing the communication interface of the RCX. Does anyone of you know, how fast the serial port of the H8 controller used in the RCX is able to work ? If you look up the (...) (23 years ago, 6-Oct-03, to lugnet.robotics)
|
| |
 | | RE: How to make a barecode?
|
|
From what I understand of VVL, CodePilot and MicroScouts: The CodePilot has pre-programed "macros" burned into ROM. Each has it's own id-code, so that's why the book can use a one-barcode "program" for each factory standard model behavior. So, I (...) (23 years ago, 6-Oct-03, to lugnet.robotics.codepilot)
|
| |
 | | Re: Wheels, Tyres and Tractions
|
|
Hi Jim, (...) Thanks ;o) (...) Definitely YES. That's why as I changed wheels I modified the test vehicule to try to keep attachment point in line with wheel center. It is also important to keep the retaining rope horizontal, to avoid the creation (...) (23 years ago, 6-Oct-03, to lugnet.robotics, FTX)
|
| |
 | | RE: Touch sensor problems
|
|
This is good advice. I've had a motor and a couple of 8448 "hydraulics" that have failed and LEGO has cheerfully replaced them. --Russ -----Original Message----- From: Mark H. Near [mailto:markn@SCOCA-K12.ORG] Sent: Sunday, October 05, 2003 4:37 PM (...) (23 years ago, 6-Oct-03, to lugnet.robotics)
|
| |
 | | Re: Touch sensor problems
|
|
(...) Hi Giacomo, Looks like that rubber part has lost its conductivity, simple thing you can try is- stick a samll aluminium piece on it annd reassemble it that would work . Nitin Mindsensors Robotics www.mindsensors.com (23 years ago, 5-Oct-03, to lugnet.robotics)
|
| |
 | | Re: Touch sensor problems
|
|
(...) Try cleaning it with warm water and a mild detergent and then use some sort of rubber/plastic restorer on it. It's probably shrunk somewhat as it's dried out over the years. If that doesn't work then scavenge a membrane keyboard. -- -- God (...) (23 years ago, 5-Oct-03, to lugnet.robotics)
|
| |
 | | Re: Touch sensor problems
|
|
My first recourse would be to contact LEGO for a replacement part. Mark Near (...) Mark (NOTE NEW PHONE NUMBERS) Mark Harrison Near markn@scoca-k12.org LAN Manager 800.634.8828 x5300 (Toll Free) 740.289.5300 (Desk) 740.352.9141 (Cell) 740.532.7752 (...) (23 years ago, 5-Oct-03, to lugnet.robotics)
|