 | | Re: BrickOS motor-output: Subject to change?
|
|
Hi Dietmar, Have you tried brickOS 0.2.6.10? Code was added to that version to address this issue. Mark "Dietmar Cordes" <cordes@lepomux.org> wrote in message news:3F0A7BA7.207050...mux.org... (...) (22 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help with lnp
|
|
(...) We finally decided to take the time and use Linux to try and get lnpd working. Although we are not familiar with Linux, our professors are helping us. Our main problem now though is the installation of brickOS. I know this should be an obvious (...) (22 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | BrickOS motor-output: Subject to change?
|
|
Hello, while doing some testing with data transfer wia the motorport of the RCX, I had (again) the problem that the output at full speed (255) is not a constant DC-output. Does anyone have a good solution for this already and will it be part of the (...) (22 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | X5 - High-speed COG-shifting biped
|
|
Introducing by far my fastest biped yet. I've clocked it at approximately 28 ft./min. or about .5 km/hour, although its speed can vary a bit depending on the surface it's run on. It is fairly compact, and it uses an improved walking mechanism that (...) (22 years ago, 7-Jul-03, to lugnet.technic, lugnet.announce.moc, lugnet.robotics)
|
| |
| | Re: robot as input device
|
|
> I assume you want to use the RCX and sensors to collect data and plot/export/do (...) Yes I would like to use sensor data to control objects in a VR-Framework. So it would be possible to use lego RCX data and map it on input device data of the (...) (22 years ago, 7-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: robot as input device
|
|
(...) I assume you want to use the RCX and sensors to collect data and plot/export/do calculations using these data. RoboLab Investigator (software) does that. You can have a bot roam around, collect sensor data of all kinds, and upload it to your (...) (22 years ago, 7-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: robot as input device
|
|
(...) I don't really understand what you want to do ...... nanobapt (22 years ago, 7-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: uCOG VI, improved leg geometry
|
|
(...) I made a video of this one walking. The amount of leg lift on this little one is quite big given that it has no knees. (URL) (22 years ago, 7-Jul-03, to lugnet.technic, lugnet.robotics, lugnet.build)
|
| |
| | Re: MOC - Small Pneumatic Biped Walker
|
|
(...) moves quite quickly. I used my best compressor for this (three large hand pumps side by side all being pumped by hand at the same time :^) (URL) (22 years ago, 7-Jul-03, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: Pneumatic Inchworm
|
|
(...) Thanks! Yes. THis one is going to brickfest. The new form factor pneumatic switches found in 8455 helped a lot, because the mounting holes are not in line with the switch rotation point. (...) Kevin (22 years ago, 7-Jul-03, to lugnet.technic, lugnet.robotics, lugnet.build)
|
