 | | Re: gear pulley/release system
|
|
I just thought of an idea, haven't had time to try it out but here it is. What if you were to have a sliding worm gear that would wind the arm up when the motor was powered forward and release it when the motor was powered reverse. Like I said, just (...) (23 years ago, 27-Jun-03, to lugnet.robotics)
|
| |
 | | Send/Receive messages under linux
|
|
Hi, I've writen a program to send messages to an RCX, depending on programable key strokes. My idea was to drive the robot "blindly", relying on standard firmware messages and replies. I've used Mr. Kekoa Proudfoot's code for packet assembly (files (...) (23 years ago, 19-Jun-03, to lugnet.robotics.rcx)
|
| |
 | | Re: A better full adder!
|
|
(...) Ah... it took me a while to figure out what you were doing, but I see now... (reviewing your pics) If your inputs to the XOR were A and B, you use A to drive the piston, and require the presence of both B and NOT B to make the piston move. I (...) (23 years ago, 26-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: A better full adder!
|
|
(...) AND takes 1 piston + 1 switch using your design. XOR takes 1 piston + 2 switches using my design. OR takes 1 piston + 2 switches using my design. But AND and XOR can be done using the same piston, so 1 piston + 3 switches gets you a half (...) (23 years ago, 26-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: A better full adder!
|
|
(...) Finally I can compete again! ;^) I can do a half adder with 1 piston and seven switches, plus you get dual polarity pressure. Three switches for AND and four for XOR. This says that I can do single pressure logic line with one piston and three (...) (23 years ago, 26-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: gear pulley/release system
|
|
"Richard Diaz" <lego-robotics@crynwr.com> wrote in message news:20030625224958....hoo.com... (...) That was the idea, yes. When the gears cames to the end of the Gear Rack, there should be enough space for the gears to flip around. My idea was that (...) (23 years ago, 26-Jun-03, to lugnet.robotics)
|
| |
 | | Re: A better full adder!
|
|
(...) It sure is. Thanks. Using the same pattern (setting up specific switches "backwards"), I can do a half adder with two pistons and 4 switches (2 switches on each piston). Again, no need for inter-piston bracing, just the requirement that a (...) (23 years ago, 26-Jun-03, to lugnet.technic, lugnet.robotics)
|
| |
 | | Re: Mechanical Memory for Computing
|
|
(...) Various network protocols define bytes as 7-bit + parity. Almost all modern modems still support this, for a simple example. Historically, the hardware-defined 'most covenient' integer size was called the 'word', with word sizes ranging from 4 (...) (23 years ago, 26-Jun-03, to lugnet.robotics)
|
| |
 | | Re: Mechanical Memory for Computing
|
|
Quoting Ross Crawford <rcrawford@csi.com>: (...) Not to start a tempest in a teapot but I know of no recent computer language or hardware which defines a byte as anything other than 8 bits. "byte-wide" I/O is always 8 bits wide as are byte-wide (...) (23 years ago, 26-Jun-03, to lugnet.robotics)
|
| |
 | | Re: A better full adder!
|
|
(...) Kevin (23 years ago, 26-Jun-03, to lugnet.technic, lugnet.robotics)
|