 | | Re: DCC for the RCX
|
| Hi Dryden, DCC sends information to the decoders by flipping the polarity of the power supply in a specific timing sequence. So, it's not like the X-10 protocol. To get more power to run more locomotives, you need something called a DCC booster. The (...) (23 years ago, 31-May-03, to lugnet.robotics.rcx, lugnet.trains)
| | |  | | Re: DCC for the RCX
|
| (...) Got the programming part--all motors on differnt Loco #'s--figured it out. I wouldn't mind building that Ack circuit though, so any advice on using hte LEGO diodes would be helpful. I'm having a great time--and by the way, as mentioned on the (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
| | |  | | Re: maze solving algorithm
|
| I'm having problems writing a program for a robot to search all the squares of a 5 X 5 maze. I'm using NQC so I'm limited in what i can do. If anyone has any ideas on how to go about searching all the squares it would be greatly appreciated. thanx (...) (23 years ago, 30-May-03, to lugnet.robotics)
| | |  | | Re: DCC for the RCX
|
| (...) Hey Mark, I posted earlier in a new thread praising the greatness of this, but I have a few additional questions that I thought I'd just ad to this thread-- I converted 3 LEGO motors with the micro-controller, and now have 3 diodes (at least, (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
| | |  | | Re: DCC for the RCX
|
| (...) hmm, color codes and being color blind dont really match well indeed... as far as electronic components go, I'm just a hobbyist. My day job is programming ;) Esger (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
| | |  | | Re: DCC for the RCX
|
| In lugnet.robotics.rcx, Esger Abbink wrote: <snip> (...) Perfectly understood. Thanks! My problem has always been that I wanted to get into electronics, but all those resistors 'n such used to have all these coloured stipes to denote the different (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
| | |  | | Re: DCC for the RCX
|
| i have a question concerning how the DCC signal is sent Is it just sort of a "rider" on top of the power similar to X-10 home automation signals? If so could not the RCX be protected with diodes and used in conjunction with a standard train (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
| | |  | | Re: DCC for the RCX
|
| (...) put in (...) Thanks, Larry, and thanks to all who posted or emailed. (...) one (...) Or is (...) It's important that the motor outputs share the load as evenly as possible. A stalled train motor can draw as much as 750ma, while a single motor (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx, lugnet.trains)
| | |  | | Re: THOUGHTS on mapping with Lego Robot ( added to searching walls)
|
| (...) What about ultrasonic beacons at each corner of the room? Then use the old-fashioned Hyperfix calculations. It should cost only a few dollars in hardware - and six months of software development :-). Are they available off the shelf or are (...) (23 years ago, 30-May-03, to lugnet.robotics)
| | |  | | Communicating between two RCX'es with cable
|
| Hi there, Long time, no see - I've finally managed to dig out my Lego once again... First of all; I'm very pleased to see the outcome of LejOS 2.x - with Proximity, LLC, integration of rcxcomm, etc. Now, I was wondering if it would be possible (...) (23 years ago, 30-May-03, to lugnet.robotics.rcx.java)
| |