 | | Re: OS Stability concerns
|
|
Actually the software was LEGO Chess, so nothing critical. I had opted to install the abbreviated version, but when I gave that computer to my kids I figured there would be room for the full one, but instead of uninstalling the shorter one, well, (...) (24 years ago, 14-May-03, to lugnet.robotics)
|
| |
 | | Re: I2C interface
|
|
Hi, Change the declaration for set_motor to: extern "C" void set_motor(unsigned char mask, unsigned char value); and you should be fine. And, yes, it's H8 asm code. Probably could have written it in C, but I tend to prefer asm for low-level type (...) (24 years ago, 13-May-03, to lugnet.robotics)
|
| |
 | | RE: COG shifter off topic
|
|
I presume you realise that COG and centroid are only equivalent for a body of uniform density? Tony -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...net.com]On Behalf Of Kevin L. Clague Sent: Wednesday, 14 May 2003 (...) (24 years ago, 13-May-03, to lugnet.robotics)
|
| |
 | | Re: I2C interface
|
|
Thanks for your answer! However, I do have some questions about it.. First of all, I looked at the code you send in your post. looks nice, but to be honest, I don't know anything about assembly ( It is assembly, whats being used in the sub (...) (24 years ago, 13-May-03, to lugnet.robotics)
|
| |
 | | Scout SDK & USB IR Tower?
|
|
Hi, I just recently downloaded the Scout SDK. I installed the software, but, I cannot get it to see my Scout. When I open the Scout Tool application an error message says "Please be sure your Scout is turned on and within range, then press init (...) (24 years ago, 13-May-03, to lugnet.robotics.scout)
|
| |
 | | Re: Slow response in RoboLab?
|
|
I've uploaded my example program to: (2 URLs) was seeing if I could program a solution for the following request from another mailing list: (URL) program seems to spend much more than the "wait" times between loops. Steve Putz (...) (24 years ago, 13-May-03, to lugnet.robotics.rcx.robolab)
|
| |
 | | Re: COG shifter off topic
|
|
(...) Besides, Mario and Giulio Ferrari use the term in their book, so it is good enough for me :^) Kevin (...) (24 years ago, 13-May-03, to lugnet.technic, lugnet.cad, lugnet.inst, lugnet.robotics)
|
| |
 | | RCX packet format
|
|
Hi, When u want to send message from the RCX for instance to a PC, what is the sequence of bytes do u follow. For example if u are sending from a remote control/PC to the RCX, I know u send something like this: 0x55 0xff 0x00 and u follow each data (...) (24 years ago, 13-May-03, to lugnet.robotics.rcx)
|
| |
 | | Packet format for sending(data) from the RCX to the PC
|
|
Hi, When u want to send message from the RCX for instance to a PC, what is the sequence of bytes do u follow. For example if u are sending from a remote control/PC to the RCX, I know u send something like this: 0x55 0xff 0x00 and u follow each data (...) (24 years ago, 13-May-03, to lugnet.robotics)
|
| |
 | | Re: Slow response in RoboLab?
|
|
Could you be more specific about your problem with container's container? Or post somewhere an example code? Claude Baumann (...) (24 years ago, 13-May-03, to lugnet.robotics.rcx.robolab)
|